Panasonic Diga DMR-EZ49V Operating Instructions Manual

Contents

83VQT2J52ReferenceDigital broadcasts cannot be received.¾ Digital broadcast may not have started in your region yet.¾ The aerial may not be pointing in the direction of the TV station,or the direction of the aerial may have changed due to strongwinds or vibration. If problem persists consult your local TVaerial installer.¾ [For]Germany[and]Austria[ Switch “Active Antenna” to “On” in theSetup menu if you are using an indoor antenna. (> 66)After DVB Auto Setup only some or no DVBchannels are found.¾ Check to ensure your area is covered by DVB transmissions.¾ Check that the aerial and antenna cable are designed for DVB.If you live within 5-10 km of DVB transmission towers, acombined VHF/UHF aerial should be adequate. Outside thisarea, separate VHF and UHF aerials provide superior receptionperformance. (> 8)Picture regularly breaks up on some channels.“No Signal” message is displayed.¾ Check “Signal Condition”. If “Signal Quality” or “Signal Strength”are displayed in red or constantly changing, check aerial. Ifproblem persists consult your local TV aerial installer. (> 63)¾ Check that the aerial and antenna cable are designed for DVB.¾ Interference (known as impulse noise) from householdappliances such as light switches, fridges etc. may causepicture break up and/or audio distortion. Use a high qualityquad shielded coaxial cable fly lead between this unit andantenna wall socket to minimise impulse noise pickup. Ifproblem persists consult your local TV aerial installer.¾ Check aerial connection.¾ Adjust the aerial reception with “DVB Manual Tuning” in theSetup menu. (> 62)Picture very infrequently breaks up on some orall channels.¾ Electrical atmospheric interference caused by local or distantlighting storms or heavy rain with wind in “leafy” locations maycause pictures to break up and audio to mute or distortmomentarily.¾ Impulse noise interference from an infrequently used electricalappliance, or a passing vehicle or lawn mower with a “noisy”ignition system.VIERA Link doesn’t work.¾ Check the HDMI cable connection. Check that “HDMI” isdisplayed on the front display when the power for the main unitis set to On.¾ Make sure that “VIERA Link” is set to “On”. (> 66)¾ Check the “HDAVI Control” settings on the connected device.¾ Some functions may not work if depending on the version of“HDAVI Control” of the connected equipment. This unit supports“HDAVI Control 5” functions.¾ If the connection for the equipment connected with HDMI waschanged, or if there was a power failure or the plug wasremoved from the household mains socket, “HDAVI Control”may not work.In this case, perform the following operations.1 When the HDMI cable is connected to all equipment with thepower on, turn the TV (VIERA) on again.2 Change the TV (VIERA) settings for the “HDAVI Control”function to off, and then set to on again. (For moreinformation, see the VIERA operating instructions.)3 Switch the VIERA input to HDMI connection with this unit,and after this unit’s screen is displayed check that “HDAVIControl” is working.The operation on this unit (music playback etc.)is interrupted.¾ The operation on this unit may be interrupted when you pressbuttons on the TV remote control that do not work for VIERALink functions.To return all the settings other than the main onesto the factory preset¾ Select “Yes” in “Shipping Condition” in the Setup menu. All thesettings except for the ratings level, ratings PIN, languagesettings and clock settings, etc. return to the factory preset. Thetimer recording programmes are also cancelled. (> 68)¾ Select “Yes” in “Default Settings” in the Setup menu. All thesettings other than the tuning settings, clock settings, countrysettings ([For]Italy[and[Spain]), language settings, disc languagesettings, ratings level, ratings PIN, remote control code, etc.return to the factory presets. The timer recording programmesare also cancelled. (> 68)¾ Press and hold [X CH] and [CH W] on the main unit until the ActiveAntenna setting menu ([For]Germany[and]Austria[) or Country settingscreen ([For]Italy[and[Spain]) appears.All the settings except for the ratings level, ratings PIN, clocksettings and remote control code, etc. return to the factorypreset. The timer recording programmes are also cancelled.To reset the ratings level settings¾ While the disc tray is open, press [DRIVE SELECT] to selectthe DVD drive, then press and hold [¥ REC] and [1] on themain unit at the same time for 5 or more seconds.To restore the unit if it freezes due to one of thesafety devices being activated¾ Press and hold [Í/I] on the main unit for 3 seconds.(The settings remain.)After performing an update, you can no longerreceive broadcasts.¾ Depending on the content of the update, some settings mayhave returned to the preset values. Fix the settings again.Digital broadcast VIERA LinkTo reset this unitOther