Panasonic LS-H A Series Instruction Manual

Panasonic LS-H A Series Instruction Manual Manual pdf 1 page image

CAUTIONS3This product has been designed to meet the specifications when it is usedalong with the optional exclusive amplifier. If an amplifier other than theexclusive amplifier is used, not only the specifications may not be met, butit may also be a cause for malfunction or break down. Hence, pleaseensure to use this product along with the optional exclusive amplifier.●●●●●●●●●●●●●●●This product has been developed / produced for industrial use only.Always use the sensor with the connector to be joined to the amplifier.Make sure that the power is off while wiring to the amplifier.In case noise generating equipment (switching regulator, inverter motoretc.) is used in the vicinity of this product, connect the frame ground(F.G.) terminal of the equipment to an actual ground.If power is supplied from a commercial switching regulator, ensure thatthe frame ground (F.G.) terminal of the power supply is connected to anactual ground.Do not use the sensor during the initial transient time (0.5 sec.) just afterthe power supply is switched on.Do not run the wires together with high-voltage lines or power lines or putthem in the same raceway. This can cause malfunction due to induction.Take care that the sensor head is not directly exposed to fluorescentlamp from a rapid-starter lamp or a high frequency lighting device, as itmay affect the sensing performance.The sensor head cable cannot be extended.Make sure that stress is not applied directly to the sensor head cablejoint.This sensor is suitable for indoor use only.Do not allow any water, oil fingerprints, etc., which may refract light, ordust, dirt, etc., which may block light, to stick to the emitting / receivingsurfaces of the sensor head. In case they are present, wipe them with aclean, soft cloth or lens paper.Do not use the sensor in vaporous, dusty or corrosive gas atmospheres.Take care that the sensor does not come in contact with water, oil,grease or organic solvents, such as, thinner, etc.Make sure that the power is off while cleaning the emitting / receivingwindows of the sensor head.SPECIFICATIONS2Notes: 1)2)3)The model No. with suffix '-C5' stands for the 5m cable length type.(e.g.) LS-H91A-C5The model No. of retroreflective type sensor with the suffix '-Y' is the sensor without the RF-330reflector. Arrange the reflector separately.(e.g.) LS-H91-A-YConfigure the mode settings in the applicable amplifier LS-400 series.Diffuse reflective type30 to 150mm30 to 150mm30 to 250mm30 to 500mmLS-H21-AConnector for amplifier: 1 pc.Warning label: 1 pc. (Chinese)Type Coaxial retroreflective typeSensingrange(Note 3)0.1 to 1mH-SP mode0.1 to 1mFAST mode0.1 to 3mSTD mode0.1 to 5mU-LG modeLS-400 seriesApplicable amplifierModel No. (Note 1)Item LS-H91-A (Note 2)Connector for amplifier: 1 pc.RF-330 (Reflector): 1 pc.Warning label: 1 pc. (Chinese)Accessories30g approx.Weight0.1mm 2 shielded cable, 2m longCableEnclosure: PBT (Attachment: PEI), Lens cover: AcrylicMaterialRed semiconductor laser Class 1 (IEC / JIS / GB standard)(Max. output: 1mW or less, Peak emission wavelength: 655nm)Emitting element-10 to +55℃ (No dew condensation or icing allowed), Storage: -20 to +70℃35～85% RH, Storage: 35～85% RHAmbient humidityAmbient temperatureGreen LED (Lights up when laser is emitted)Laser emission indicatorOrange LED (Lights up when amplifier output is ON)Operation indicator●●●●Never use this product as a sensing device for personnel protection.In case of using sensing devices for personnel protection, useproducts which meet laws and standards, such as OSHA, ANSI or IECetc., for personnel protection applicable in each region or country.Although this product corresponds to a Class 1 laser product, it isdangerous to see the laser beam which has been passed through aviewing optical system such as a lens etc. Hence, please avoid this.Use of control or adjustment or performance of proceduresother than those specified in this instruction manual mayresult in hazardous radiation expose.WARNINGFOR SAFE USE OF A LASER PRODUCT1●・The following label is affixed on this product in accordance with theSafety of laser product.Warning labelIn Japanese (Based on JIS C 6802) In English (Based on IEC 60825-1)LS-H□-ALaser Sensor HeadINSTRUCTION MANUALMJE-LSHA No.0075-18V● In order to prevent the accident by laser product and protect the users,JIS C 6802 -2014 “Safety of laser products” was established based on theregulation of IEC (International electrotechnical Commission). Thisregulation classifies laser products according to the level of hazard, andprovides the safety measures for respective classes.This product are classified as “Class 1 laser products” according toIEC 60825-1 -2014 (JIS C 6802 -2014) “Safety of laser products”.● Laser hazardous classClassification according to IEC 60825-1 -2014 (JIS C 6802 -2014 )Safe under reasonably foreseeable conditions of operationClass 1Description of hazardous evaluationClass・ Laser emission indicator (green)While laser is emitted, the laser emission indicator (green) of the sensorhead lights up.This indicator is visible even when wearing laser protective glasses.Operation indicator (Orange)Laser emission indicator (Green)Direction oflaser emissionIn Chinese (Based on GB 7247.1 -2012 )● When this product is used in China,affix the Chinese warning label (acces-sory) on the label in the product.Direction oflaser emissionDirection oflaser emissionThank you very much for purchasing Panasonic products.Read this Instruction Manual carefully and thoroughly for the correct andoptimum use of this product.Kindly keep this manual in a convenient place for quick reference.

/ 2

Related manuals for Panasonic LS-H A Series