Panasonic LS-H F-A Series Instruction Manual

Panasonic LS-H F-A Series Instruction Manual Manual pdf 1 page image

Thank you very much for purchasing Panasonic products. Read this InstructionManual carefully and thoroughly for the correct and optimum use of this product.Kindly keep this manual in a convenient place for quick reference.●●●●Never use this product as a sensing device for personnel protection.In case of using sensing devices for personnel protection, useproducts which meet laws and standards, such as OSHA, ANSI orIEC etc., for personnel protection applicable in each region or country.Although this product corresponds to a Class 1 laser product, it isdangerous to see the laser beam which has been passed through aviewing optical system such as a lens etc. Hence, please avoid this.Use of control or adjustment or performance of procedures otherthan those specified in this instruction manual may result inhazardous radiation expose.WARNINGCAUTIONS3This product has been designed to meet the specifications when it is usedalong with the optional exclusive amplifier. If an amplifier other than theexclusive amplifier is used, not only the specifications may not be met, but itmay also be a cause for malfunction or break down. Hence, please ensure touse this product along with the optional exclusive amplifier.●●●●●●●●●●●●●●●This product has been developed / produced for industrial use only.Always use the sensor with the connector to be joined to the amplifier.Make sure that the power is off while wiring to the amplifier.In case noise generating equipment (switching regulator, inverter motor etc.)is used in the vicinity of this product, connect the frame ground (F.G.)terminal of the equipment to an actual ground.If power is supplied from a commercial switching regulator, ensure that theframe ground (F.G.) terminal of the power supply is connected to an actualground.Do not use the sensor during the initial transient time (0.5 sec.) just after thepower supply is switched on.Do not run the wires together with high-voltage lines or power lines or putthem in the same raceway. This can cause malfunction due to induction.Take care that the sensor head is not directly exposed to fluorescent lampfrom a rapid-starter lamp or a high frequency lighting device, as it may affectthe sensing performance.The sensor head cable cannot be extended.Make sure that stress is not applied directly to the sensor head cable joint.This sensor is suitable for indoor use only.Do not allow any water, oil fingerprints, etc., which may refract light, or dust,dirt, etc., which may block light, to stick to the emitting / receiving surfaces ofthe sensor head. In case they are present, wipe them with a clean, soft clothor lens paper.Do not use the sensor in vaporous, dusty or corrosive gas atmospheres.Take care that the sensor does not come in contact with water, oil, grease ororganic solvents, such as, thinner, etc.Make sure that the power is off while cleaning the emitting / receivingwindows of the sensor head.SPECIFICATIONS2Notes: 1)2)The model No. of retroreflective type sensor with the suffix '-Y' is the sensor without the RF-330reflector. Arrange the reflector separately.(e.g.) LS-H91F-A-YConfigure the mode settings in the applicable amplifier LS-400 series.Diffuse reflective type30 to 150mm30 to 150mm30 to 250mm30 to 500mmLS-H21F-AConnector for amplifier: 1 pc.Explanation label (JIS) : 1 pc.Type Coaxial retroreflective typeSensingrange(Note 2)0.1 to 1mH-SP mode0.1 to 1mFAST mode0.1 to 3mSTD mode0.1 to 5mU-LG modeLS-400 seriesApplicable amplifierModel No.Item LS-H91F-A (Note 1)Connector for amplifier: 1 pc.RF-330 (Reflector): 1 pc.Explanation label (JIS) : 1 pc.Accessories30g approx.Weight0.1mm2 shielded cable, 2m longCableEnclosure: PBT (Attachment: PEI), Lens cover: AcrylicMaterialRed semiconductor laser Class 1 (FDA / IEC / JIS standard)(Max. output: 1mW or less, Peak emission wavelength: 655nm)Emitting element-10 to +55℃ (No dew condensation or icing allowed), Storage: -20 to +70℃35～85% RH, Storage: 35～85% RHAmbient humidityAmbient temperatureGreen LED (Lights up when laser is emitted)Laser emission indicatorOrange LED (Lights up when amplifier output is ON)Operation indicatorINSTRUCTION MANUALLS-H□F-A Conforming to FDALaser Sensor HeadMJE-LSHFA No.0059-45V・ Laser emission indicator (green)While laser is emitted, the laser emission indicator (green) of the sensor headlights up.This indicator is visible even when wearing laser protective glasses.Operation indicator (Orange)Laser emission indicator (Green)Direction oflaser emissionFOR SAFE USE OF A LASER PRODUCT1●●With regard to safety of laser products, IEC 60825-1 -2014 'Safety of laserproducts' has been stipulated by the IEC (International Electrotechnical Commis-sion). In IEC 60825-1 -2014 , laser products are divded into classes correspondingto the degree of danger of the laser component, and preventive measures toassure safety which should be taken with each class are stipulated.This product is classified as a 'Class 1 laser product' by IEC 60825-1 -2014 .This product complies with 21 CFR 1040.10 and 1040.11 Laser Notice No. 50, datedJune 24, 2007, issued by CDRH (Center for Devices and Radiological Health) underthe FDA (Food and Drug Administration). For details, refer to the Laser Notice No. 50.● Classification of laser product (IEC 60825-1 -2014 )Safe under reasonably foreseeable conditions.Class 1Description of hazard classClassification● Summary of the safety precautions for user of a laser product (IEC 60825-1 -2014 )●・The following labels are affixed on this product in accordance with the FDAand IEC 60825-1 -2014 standard.Warning label(Label based on IEC 60825-1 -2014)(Label based on FDA)Note: When this product is used based on JIS / IEC standard, affix the accessory explanation labelon the 'Label based on FDA'.Directionof laseremissionDirectionof laseremissionTrainingEmission indicatordeviceWarning signsBeam pathSpecular reflectionEye protectionProtective clothingNot requiredNot requiredNot requirementsNo requirementsNo requirementsNo requirementsNot requiredNot required but recommended for applications that involve directviewing of the laser beam1Beam attenuatorprotectionLaser safety officerClassNot requiredRemote interlockNot requiredNot requiredKey controlNote: This table is intended to provide a convenient summary of precautions. See text of IECstandard for complete precautions.

/ 2

Related manuals for Panasonic LS-H F-A Series