Panasonic MINAS-BL GP series Technical Instructions

Contents

－ 13 －－ 12 －EC DirectivesThe EC directives apply to all such electronic products as those having specific functionsand directly sold to general consumers in EU countries. These products are required tomeet the EU unified standards and to be furnished with CE marking.Our brushless motor meet the EC Directives for Low Voltage Equipment so that themachine or equipment comprising our AC servo can meet relevant EC Directives.EMC DirectivesOur brushless motor can meet EMC Directives and related standards. However, to meetthese requirements, the systems must be limited with respect to configuration and otheraspects, e.g. the installation and some special wiring conditions must be met. This meansthat in some cases machines and equipment comprising our servo systems may not satisfythe requirements for wiring and grounding conditions specified by the EMC Directives.Therefore, conformance to the EMC Directives (especially the requirements for emissionnoise and noise terminal voltage) should be examined based on the final products thatinclude our system.Applicable standardApplicable standard InstallationconditionUL UL508 Ｃ Standard for electric converter equipmentClass I equipmentPollution degree 2SCCR *1CEEN61800-5-1 Adjustable speed electrical power drive systems.– Safety requirements. Electrical, thermal and energyEN61800-3 Adjustable speed electrical power drive systems.– EMC requirements and specific test methodsEN55011 Radio interference wave characteristics of industrial,scientific, and medical high-frequency equipmentEN61000-6-2 Standards for immunity in industrial environment(EMC directive)Overvoltagecategory IIClass I equipmentPollution degree 2KC Korea Radio Law *2 Class A Instrument(commercial broadcast communications equipment) —*1 SCCR: Symmetrical current 5,000 Arms, Max. 240 VMotor over-temperature protection is not provided.Motor over-load-temperature protection shall be provided at the final installation uponrequired by the NEC (National Electric Code).*2 Information related to the Korea Radio LawThis brushless amplifier is a Class A commercial broadcasting radio wave generatornot designed for home use. The user and dealer should be aware of this fact.Brushless AmplifierConformance to EC directive and UL standard Conformance to EC directive and UL standardConfiguration of peripheral equipmentPowersupply・100 V system: Single phase 100 V to 120 V ± 10%, 50/60 Hz200 V system: Single phase 200 V to 240 V ± 10%, 50/60 Hz・Use the equipment under the environment of overvoltage category II specified byIEC60664-1.・In order to obtain overvoltage category III, insert a transformer conforming to ENstandard or IEC standard to the input of brushless motor.・Use an electric wire size suitable to EN60204-1.MCCB(breaker)FuseBe sure to connect a specified MCCB certified by IEC standard and UL, or a fusecertified by UL between power supply and noise filter. Observance of this conditionallows conformance with UL508C (file No. E164620) .NoisefilterWhen installing one noise filter at the power supply for more than one brushlessmotor used, contact the manufacturer of noise filter.SurgeabsorberInstall a surge absorber on the primary side of noise filter. However, in performingthe voltage resistance test of machine and equipment, be sure to remove the surgeabsorber; otherwise, the surge absorber may be ruptured.GroundingBe sure to connect the grounding Terminal of brushless amplifier and protectivegrounding wire (PE) of system for preventing electric shock. Do not tighten thegrounding wires together but connect them individually.Wiring of peripheral equipmentMolded CaseCircuit Breaker(MCCB)or FuseBrushlessamplifierBrushlessmotorSurgeabsorberNoise filterProtection ground(PE)groundPowersupplyFerrite core (Noise filter for signal line)option DV0P1460 (*Qty. 4 ) (part No.: ZCAT3035-1330/TDK Corp.)* The ferrite core should insert oneor more pieces in an electric wire,respectively.List of compatible peripheral equipmentPart name Optional partnumber (option)Manufacturer'spart No. Qty. ManufacturerNoise filter(single phase) DV0P4170 SUP-EK5-ER-6 1OKAYA ELECTRICIND. CO., LTD.Noise filter(3-phase) DV0PM20042 3SUP-HU10-ER-6 1Surge absorber(single phase) DV0P4190 R・A・V-781BWZ-4 1Surge absorber(3-phase) DV0P1450 R・A・V-781BXZ-4 1Noise filter for control signals DV0P1460 ZCAT3035-1330 4 TDK Co.Ltd,.Recommended circuit breakerMade by Sensata Technologies Japan Limited:Type IELH-1-11-63-5A-M (single phase) Type IELH-1-111-63-5A-M (3-phase)(Rated current 5A, cutoff characteristics DELAY63)• Recommended cutoff characteristics: DELAY61-63

/ 9

Related manuals for Panasonic MBEG1E1BCP