Panasonic NV-GS1 User Manual

Contents

43ªTo Change the Counter Display ModeBy changing [C.DISPLAY] on the [DISPLAY SETUP]Sub-Menu, you can change the Counter Display Mode toTape Counter Indication [COUNTER] (0:00.00), MemoryCounter Indication [MEMORY] (M0:00.00), and Time CodeIndication [TIMECODE] (0h00m00s00f).(l12) Byrepeatedly pressing the [COUNTER] Button on the RemoteController, you can change the Counter Display Mode.ªTo Display Date/Time IndicationTo display Date/Time Indication, set the appropriateDate/Time in [DATE/TIME] on the [DISPLAY SETUP]Sub-Menu.(l12)You can also press the [DATE/TIME] Button of the RemoteController repeatedly to display or change the Date/TimeIndication.ªTo Change the Display ModeBy changing [DISPLAY] on the [DISPLAY SETUP]Sub-Menu, you can change the Display Mode to All FunctionDisplay [ALL], Partial Display [PARTIAL] and MinimumDisplay [OFF].~~~~~~~~~~~~~~~~~~~Owner IDYou can register your name and address in your MovieCamera to identify the owner.1 Set [CAMERA FUNCTIONS] >> [OTHERFUNCTIONS] >> [OWNER ID SET] >> [YES].≥The [OWNER ID] Menu appears.2 Turn the [PUSH] Dial to select [PIN NUMBER]and press the [PUSH] Dial to input desirednumbers.3 Turn the [PUSH] Dial to select numbers andpress the [PUSH] Dial to enter them.≥You can input 4 digits.4 Push the Operation Lever towards [∫∫∫∫] .5 Repeat Steps 2–4 to input desired charactersfor [NAME]/[POSTCODE].≥You can input up to 12 characters in [NAME], and up to11 characters in [POSTCODE].6 Push the Operation Lever towards [∫] to finishthe setup.To verify Owner ID≥Keep pushing the Operation Lever towards [;] forapproximately 5 seconds.To Check Owner IDIf Owner ID has already been set, carrying out Step 1 abovewill display [INPUT PIN NUMBER] on the screen. Input thePin Number you have already selected. If the number is notcorrect, the screen will not change. If the number is correct,the contents of the setup will be displayed. (By repeatingSteps 2 to 4 above, you can change the contents.)~~~~~~~~~~~~~~~~~~~Warning/Alarm IndicationsIf any one of the following indications lights up or flashes,please check the condition of the Movie Camera.≥Some Indications may not be displayed according to the model.3: Condensation has occurred.(l49)Y: The accidental erasure preventionslider on the inserted Cassette isopen (that is, set to [SAVE]).You are about to do audio dubbingon the unrecorded (blank) portion ofthe tape.No Cassette is inserted.(l10)6: The Battery is low. Recharge it.(l9)0: The built-in battery is low.(l16):: The video heads are dirty.(l49)2END: The tape came to end duringrecording.REMOTE: Wrong Remote Controller Mode hasbeen selected.(l8)PRINTER ERROR: The Video Printer is not connectedcorrectly, or the Video Printer is notfunctioning properly.UNPLAYABLE TAPE(OTHER FORMAT): You are attempting to play back atape section that has been recordedwith a different TV system.UNABLE TO A. DUB(LP RECORDED): Because the original recording wasdone in LP Mode, audio dubbingcannot be performed.INCOMPATIBLETAPE: This Cassette is incompatible.PLEASE RE-OPERATEAFTER PUSHINGRESET BUTTON: Mechanism Irregular is detected.Press the [RESET] Button(l6).This may solve the problem.You are attempting to record to aMemory Card formatted with another equipment (like a PersonalComputer). Format the MemoryCard with this equipment.TO SERVICE: It is a malfunction.CARD FULL: Card does not have sufficientmemory remaining.Select Card Mode and deleteunnecessary files.NO CARD: Card is not inserted.NO FILE: Card has no files recorded on it.CARD ERROR: This Card is not compatible with thisMovie Camera.COPY INHIBITED: Because the medium is protected bya copy guard, images cannot berecorded correctly.INCORRECTOPERATION: You are attempting to record to atape in VCR Mode.In NV-GS5,[TAPE/CARD/CARD MODE]Selector is set to [MPEG4] or[VOICE] when [PHOTO SHOT]Button is pressed.You are attempting to record to atape in Card Mode.~~~~~~~~~~~~~~~~~~~Notes and HintsªConcerning the Power Supply≥When the Movie Camera is used for a long time, theCamera body becomes warm, but this is not a malfunction.≥If the [CHARGE] Lamp does not light up although theBattery is attached to AC Adaptor, detach the Battery andreattach it.≥Battery CGP-D110 and CGP-D105 cannot be charged withthis AC Adaptor.