Panasonic PT-56TWD63 Operating Manual

Also see for PT47WXD63G - 47" PROJECTION TV: Service manual Service manual

Contents

Panasonic PT-56TWD63 Operating Manual Manual pdf 27 page image

M ENU OPERATIONS25 zENGLISHSet UpThis menu lets you select antenna, program channels,select analog and digital closed caption, Convergence,Auto Power On, Image Shift and Zoom Adjust.Procedure• Press MENU to display the Main Menu.• Press TCH, CHS, W VOL or VOL X to select theSetup icon.• Press OK button to display the options in the Setupmenu.Program CHThis menu allows you set up the antenna, auto scan all availableanalog and digital channels, manually add or delete channels anddisplay the signal strength of the digital channels. Input Setup - Lets you specify Antenna mode (Cableonly, Cable/Antenna or Antenna only).Note: You can connect either a Cable antenna or a terrestrialantenna to Ant A. However, if you have both Cable signaland terrestrial antenna signal, the Cable signal must beconnected to the Ant A input on the back of theprojection television. Connect the antenna signal to theAnt B input.Procedure• In Set Up menu, select Program Channel and press OK.• Press OK to enter sub-menu. Press W VOL or VOL X toselect Cable Only, Cable/Antenna or Antenna Only.• Press OK button to enter your selection. When the nextscreen will be displayed, press OK button to start theAuto scan. Auto scan must be done when you select theinput signal for the first time or whenever you change theantenna configuration.Notes:• If Cable Only, Antenna Only or Antenna/Cable isselected and DCM (Digital Cable Module) is not in, theAuto scan will perform Scan All.• If Cable Only is selected and DCM is in, Auto scan willbe skipped.• If Cable/Antenna is selected and DCM is in, Antenna (B)Analog & Digital Auto scan will be performed. Auto Scan - To automatically Scan All availablechannels, Antenna (A) Analog, Antenna (A) Analog &Digital, Antenna (B) Analog and Antenna (B) Analog &Digital.Procedure• Highlight Auto Scan and press OK to enter the submenu.• Use T CH and CH S to select and press OK to start theauto scan. After Auto Scan is completed press MENU toreturn to the previous screen. Manual Program - To add or delete channels fromeither channels list (A/B) manually. Signal Meter - Displays the signal strength of the ATSCdigital channel in either Antenna (A) or Antenna (B).Note: Signal meter feature is not available for analog channels.Procedure• Highlight Signal Meter and press OK button to enter thesub-menu.• In the RF Input field, select either Antenna (A) orAntenna (B).• Select the channel number using W VOL or VOL Xbuttons.• Press OK button to display the Signal Strength.Note: The color of the signal bar usually indicates the strengthof the received signal.• Green - Adequate signal for a good reception.• Yellow - Poor signal strength.• Red - Very poor signal strength.Program ChannelInput SetupManual ProgramSignal MeterAuto ScanOKCable onlyWWConnect Cable to Antenna (A)Change your Input Setupand press OKProgram ChannelInput SetupManual ProgramSignal MeterAuto ScanOKConnect Cable to Antenna (A)WWCable onlyAuto scan is neededpress OK to start Auto ScanProgram ChannelInput SetupManual ProgramSignal MeterScan AllAntenna (A) AnalogAntenna (A) Analog & DigitalAntenna (B) AnalogAntenna (A) Analog & DigitalPress OK to channel scanall available channelsAuto ScanOKProgram ChannelInput SetupManual ProgramSignal MeterAuto ScanRF InputChannel AddAntenna (A)Channel Delete A: 12TSW XEXITMENUto returnSELECT OKProgram ChannelInput SetupAuto ScanManual ProgramSignal MeterRF Input Antenna (A)________RF Channel 3-1W XSignal Strength: 70%Peak: : 75%