Panasonic S-200PE2E5 Technical Data & Service Manual

Also see for S-100PU2E5A: Operating instructions Operating instructions

Contents

Panasonic S-200PE2E5 Technical Data & Service Manual Manual pdf 247 page image

8Control of 2WAY SYSTEM2. Wireless Remote Controller4. Setting Address Switches5. Test operation Main/Sub setting  Address settingRemove the top case of the receiver for setting.Main/Sub setting1 2 3 4SwitchONOFF Use this to set Main/Sub for the remote controller and the receiver. Set one to [Main] and the other to [Sub]. Factory default: [Main] It is recommended to set the wired remote controller to [Main].BUSNIAMbuS/niaMMain/Sub switch position1 2 3 4 1 2 3 4Address setting When more than 1 receiver is installed in the same room, setting addresses prevents interference. For how to change addresses of wireless remote controllers, see operating instructions of wireless remote controllers.Wirelessremote controlleraddress displayAddress Address Address Address Address Address AddressALL 1 2 3 4 5 6Addressswitch positionReceiving ispossible at alladdress positions. 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4Preparation : Turn on the circuit breaker of units and then turn the power on. After the power is turned on, remote controller operation is ignoredfor approx. 1 minute because setting is being made. This is not malfunction. (Contents received while setting are disabled.)1. To start test operation, press and hold the emergency operation button for 10 seconds.2. The indication lamps (OPERATION, TIMER, STANDBY) blink during test operation..sdnoces01rofnottubnoitarepoycnegremeehtdlohdnasserp,noitarepotsethsinifoT.3Attention Do not use this mode for purposes other than the test operation.(To prevent overload of the units) Read the installation instructions supplied with the units. Any of the Heat, Cool and Fan operations can only be performed. Temperature cannot be changed. The test operation mode is automatically turned off in 60 minutes.(To prevent continuous test operation) Outdoor units do not operate for approx. 3 minutes after the power isturned on or operation is stopped.Self-diagnostics table and detected contents The "Alarm Display" as shown in the table below expresses the alarm contents displayed when the wired remote controller is connected. Forhow to handle the alarms, see installation instructions of indoor units or technical guide.reviecerehtnopmalnoitacidnIstnetnocdetceteDAlarm Display OPERATION TIMER STANDBY BlinkingCommunication error in the remote controller circuit E01–E03, E08–E14, E17, E18   Communication error either in the in/outdoor operation line orthe sub-bus of the outdoor unit E04–E07, E15, E16, E19–E31   Operation of indoor protection device P01, P09–P14    Alternately13P–51P,80P–20PecivednoitcetorproodtuofonoitarepO    Alternately11F–01F,30F–10FrotsimrehtroodniehtnirorrE    Alternately82F–21F,90F–40FrotsimrehtroodtuoehtnirorrE    Alternately92FMORPEEroodniehtnirorrE    Simultaneously13F,03FMORPEEroodtuoehtnirorrE    Simultaneously13H–10HrosserpmocehtotdetalerrorrE   90L–50L,30L–10LsgnittesroodninirorrE    Simultaneously13L–01L,40LsgnittesroodtuonirorrE    SimultaneouslyInconsistency in Air/Heat (Including an auto-temp settingfor a model without auto-temp settings)    AlternatelyOil Alarm (Same as operation of outdoor protection device)    AlternatelyTest operation    Simultaneously: OFF : ON (Illuminated) : Blinking (0.5 seconds interval)8-19AMP Air Conditioningwww.ampair.co.uk | sales@ampair.co.uk