Panasonic TC-P58V10 Operating Instructions Manual

Also see for TC-P58V10: Operating instructions Manual de instrucciones

Panasonic TC-P58V10 Operating Instructions Manual Manual pdf 23 page image

44 45AdvancedNetwork SettingNetwork SettingThis is a setting for connecting to a broadband environment.■ Press to exit froma menu screen■ Press to returnto the previousscreenDisplay menuSelect “Setup”MenuPictureAudioTimerLockVIERA LinkSD cardClosed captionSetupselectset or nextSelect “Network setting”Setup 2/2Advanced setupAboutReset to defaultsVIERA Link settingsNetwork settingVIERA CAST settingNetwork Cameras listECO/energy savingselectSelect the item and adjustNetwork setting 2/2MAC address 12-34-56-78-80-abLAN speed setting AutomaticLAN speed 10BASE half duplexSoftware updateNetwork setting 1/2Connection test SucceededIP setting mode AutomaticIP address 192.168.0.5Subnet mask 255.255.255.0Default gateway 192.168.0.254DNS setting mode OKPrimary DNS 192.168.0.20AutomaticSecondary DNS 192.168.0.21selectadjustThe network settings become effective when you close the menu and run “Connection test”.ConnectiontestCheck that the network settings are as shown below, and then start “Connection test”.Select “Connection test” and press OK. Succeeded : “Connection test” succeededOnly home network:Home network is available.Failed: Check the broadband environment connectionand settings and the network settings, and thenperform the test again.Test in progress---: Test not yet performed*Press OK again to cancel the test.(It takes a while to cancel the test.)Network setting 1/2Connection test SucceededIP setting mode ManualIP address 192.168.0.5Subnet mask 255.255.255.0Default gateway 192.168.0.254selectokIP setting• IP settingmode• IP address• Subnet mask• DefaultgatewaySelect “IP setting mode” and set to “Automatic”. ■ Manual settingSelect “IP setting mode” and set to “Manual”Select the item and press OKCheck the specifications of the broadband router andenter each IP address.(When IP automatic acquisition in DHCP can be used)Network setting 1/2Connection test SucceededIP setting mode AutomaticIP address 192.168.0.5Subnet mask 255.255.255.0Default gateway 192.168.0.254The acquired address is displayed.selectok Subnet mask OK10 I0 . 0 . 0 . 0changechannelokorEach IP address is acquired automatically.DNS setting• DNS settingmode• Primary DNS• SecondaryDNSSelect “DNS setting mode” and set to “Automatic”.(When DNS automatic acquisition in DHCP can be used)Network setting 1/2Connection test SucceededIP setting mode AutomaticDefault gateway 192.168.0.254DNS setting mode OKPrimary DNS 192.168.0.20AutomaticSecondary DNS 192.168.0.21The acquired address is displayed.selectokEach IP address is acquired automatically.If you are using a broadband router, IP automaticacquisition in DHCP can be used under normalcircumstances. If you are not sure, check with theperson who installed the equipment, or check theinstructions for each device.■ Manual settingSelect “DNS setting mode” and set to “Manual”Select the item and press OKEnter each IP address as was specified by theprovider.Primary DNS 10 I0 . 0 . 0 . 0selectokorConnectionspeedsetting• LAN speedsetting• LAN speedSelect “LAN speed setting” (Default is “Automatic”) Normally, select “Automatic”.If “Connection test” failed, set the “LAN speed setting”to “manual” and then select “10BASE half duplex”,“10BASE duplex”, “100BASE half duplex” or “100 BASEduplex”.Cannot be selected when the “LAN speed setting” is“Automatic”.Changing the settings may make it impossible toconnect some types of equipment.Network setting 2/2MAC address 12-34-56-78-80-abLAN speed setting AutomaticLAN speed 10BASE half duplexSoftware updateselectadjustSoftwareupdateSelect “Software update” Press OK to start the software update screen.Follow directions of the screen.* Set “Clock” first. (p. 18)Network setting 2/2OKMAC address 12-34-56-78-80-abLAN speed setting AutomaticLAN speed 10BASE half duplexSoftware updateselectok