Panasonic WJ-MP204 Operating Instructions Manual

Also see for WJMP204 - MULTIPLEX UNIT: Operating instructions

19ON: Multiplex sync signals (VD2) are generated by syn-chronizing with the signals sent to the VS/VD INconnector. If there is no input signal, the internallygenerated sync signal (VD2) is multiplexed.OFF: Sync signal (VD2) is not multiplexed.THRU: The sync signal (VD2) sent to the CAMERA OUTconnector is multiplexed with the video signals. Ifthere is no input signal, the sync signal (VD2) is notmultiplexed.The initial factory setting is ON.• Data Setting1. Display the SYSTEM menu.2. Move the cursor to DATA by pressing button 1 (C) orbutton 2 (D), press the SUSPEND/SET button, thenselect data communication ON or OFF by pressing but-ton 3 (–) or button 4 (+).The initial factory setting is ON.(3) VS/VD Input1. Display the SYSTEM menu.2. Move the cursor to VS/VD INPUT by pressing button 1(C) or button 2 (D), then select VS or VD by pressingbutton 3 (–) or button 4 (+).The initial factory setting is VD.(4) Daisy Mode1. Display the SYSTEM menu.2. Move the cursor to DAISY MODE by pressing button 1(C) or button 2 (D), then select control mode ON orOFF by pressing button 3 (–) or button 4 (+).The initial factory setting is ON.(5) Terminal1. Display the SYSTEM menu.2. Move the cursor to TERMINAL by pressing button 1 (C)or button 2 (D), then select ALARM or REMOTE bypressing button 3 (–) or button 4 (+).The initial factory setting is ALARM.Note: To switch from ALARM/REMOTE IN to ALARM/REMOTE OUT, shift the internal connector of the WJ-MP204 from the ALM IN connector to the ALM OUTconnector (See page 24).The initial factory setting of ALARM/REMOTE connectoris ALM IN.• Camera Input Setting1. Display the SYSTEM menu.2. Move the cursor to CAMERA IN by pressing button 1(C) or button 2 (D), press the SUSPEND/SET button,then select the desired channel 1, 2, 3 or 4 for back-ground picture by pressing button 3 (–) or button 4 (+).The initial factory setting is 1CH.• Cable Compensation Setting1. Display the SYSTEM menu.2. Move the cursor to COMP by pressing button 1 (C) orbutton 2 (D), press the SUSPEND/SET button, thenselect the most suitable cable length by pressing but-ton 3 (–) or button 4 (+).S: Less than 400 m (1,300 ft)M: 400 m (1,300 ft) to 700 m (2,300 ft)L: 700 m (2,300 ft) to 900 m (3,000ft)(When using RG-59U, BELDEN 9259 or equivalentcable)The initial factory setting is S.• VD2 Setting1. Display the SYSTEM menu.2. Move the cursor to VD2 by pressing button 1 (C) orbutton 2 (D), press the SUSPEND/SET button, thenselect ON, OFF, or THROUGH by pressing button 3 (–)or button 4 (+).COMP/VD2/DATACAMERA IN 1CHCOMP SVD2 ONDATA ON• Alarm DataThis is to set whether or not the alarm data receivedfrom a camera is to be transmitted to the WV-CU360.POLLING: Disables to transmit to the system controllereven if an alarm is activated.AUTO1: Enables to transmit to the system controllerwhen an alarm is activated.AUTO2: Enables to transmit to the system controllerwhen an alarm is activated. Ignores an alarm for 5seconds after it has transmitted. Enable to transmitan alarm after it has elapsed for 5 seconds.1. Display the SYSTEM menu.2. Move the cursor to ALARM DATA by pressing button 1(C) or button 2 (D), then select the desired alarm datamode, POLLING, AUTO1, or AUTO2, by pressing but-ton 3 (–) or button 4 (+).The initial factory setting is AUTO2.(2) Comp/VD2/Data Setting