Panasonic WV-CW590G Operating Instructions Manual

Also see for WV-CS580: Specifications Preliminary

Contents

Panasonic WV-CW590G Operating Instructions Manual Manual pdf 4 page image

4RS485 setupThe following procedure is to configure the RS485setup when using the system controller to control thecamera (pan, tilt, etc.) via the camera's data port.1. Display the advanced setup menu (page 8), movethe cursor to COMMUNICATION , and then pressthe CAM (SET) button.This will display the RS485 setup menu.2. Check the unit number. (Installation Guide)The UNIT NUMBER item shows the unit numberspecified by DIP Switch 1.The factory default unit number is 1.If DIP Switch 1 specifies 1 to 96 as the unit number,move the cursor to UNIT NUMBER and then tilt thejoystick left or right to select a unit number (1 to 96).Note:• It is not necessary to configure the RS485 SET UPmenu SUB ADDRESS setting.• Turn on the power and use DIP Switch 1 toconfigure RS485 communication parameters.When PELCO D is set using DIP SW, ----P isdisplayed for SUB ADDRESS. In addition, to setthe PELCO D Unit Number to 32-254 using DIPSW, tilt the joystick left or right to change UnitNumber from the menu.3. Move the cursor to BAUD RATE, and then tilt thejoystick left or right to select a baud rate setting.Tilting the joystick cycles through the baud rate(transmission speed) display in the sequenceshown below. (unit: bits/s)The factory default setting is 19200.4. Move the cursor to DATA BIT, and then tilt thejoystick left or right to select a data bit setting (7 or8).The factory default setting is 8.5. Move the cursor to PARITY CHECK, and then tilt thejoystick left or right to select a parity bit setting(NONE, ODD, EVEN).The factory default setting is NONE.6. Move the cursor to STOP BIT, and then tilt thejoystick left or right to select a stop bit setting (1 or2).The factory default setting is 1.7. Move the cursor to XON/XOFF, and then tilt thejoystick left or right to select an XON/XOFF setting.NOT USE : Disables XON/XOFF data flow control.USE : Enables XON/XOFF data flow control.The factory default setting is NOT USE.8. Move the cursor to WAIT TIME, and then tilt thejoystick left or right to select a wait time setting.The wait time is the time that the camera shouldwait before resending data when no receiveacknowledgement (ACK) is returned after data issent.Tilting the joystick cycles through the wait timedisplay in the sequence shown below. (unit: ms)The factory default setting is OFF.9. Move the cursor to ALARM DATA, and then tilt thejoystick left or right to select an alarm data sendmode setting.POLLING : Sends alarm data in response to arequest by the system controller.AUTO1 : Sends alarm data each time an alarmsignal is input.AUTO2 : Sends alarm data at five-second intervals.The factory default setting is AUTO2.10. Move the cursor to DELAY TIME, and then tilt thejoystick left or right to select a delay time setting.The delay time is the time the camera should waitbefore sending a receive acknowledge (ACK). Thedelay time display changes in the sequence shownbelow. (unit: ms)The factory default setting is OFF.This setting can be configured only when 2-lineconfiguration is selected by DIP Switch 2.(Installation Guide)**RS485 SETUP**UNIT NUMBERSUB ADDRESSBAUD RATEDATA BITPARITY CHECKSTOP BITXON/XOFFWAIT TIMEALARM DATADELAY TIMERET TOP1-----192008NONE1NOT USEOFFAUTO2---2400 4800 9600 19200OFF ↔ 100MS ↔ 200MS ↔ 400MS ↔ 1000MSOFF ↔ 100MS** RS485 SETUP **UNIT NUMBERSUB ADDRESSBAUD RATEDATA BITPARITY CHECKSTOP BITXON/XOFFWAIT TIMEALARM DATADELAY TIMERET TOPP1 D32----P192008NONE1NOT USEOFFAUTO2OFF[RS485 SETUP] MenuUsing a joystick,etc., set the unitnumber (32 to 254).(The illustrationshows that the unitnumber is set to 32.)