Ambient operating temperature: –50 °C to +60 °C {–58 °F to +140 °F}Dimensions: ø58 mm × 85 mm (H){ø2-9/32 inches × 3-11/32 inches (H)}Mass: Approx. 200 g {0.44 lbs}Finish: Aluminum die cast Fine silver (WV-Q123A)Light gray (WV-Q179)i-PRO white (WV-QAT500-W)avs0520-0Printed in ChinaAttachment Pipe BracketModel No. WV-Q123AWV-Q179WV-QAT500-WOperating InstructionsIncluded Installation Instructions• Before attempting to connect or install this product, please read these instructions carefully andsave this manual for future use.• The external appearance and other parts shown in this manual may differ from the actual productwithin the scope that will not interfere with normal use due to improvement of the product.PrefaceThis product is used to mount the camera on a locally procured mounting bracket.For the latest information about the supported cameras, refer to our support website(https://security.panasonic.com/training_support/support/info/ ).SpecificationsRefer installation work to the dealer.Installation work requires technique and experience. Failure to observe this may cause fire, electricshock, injury, or damage to the product.Be sure to consult the dealer.Do not use this bracket except with specified cameras or mount brackets.Failure to observe this may cause a drop resulting in injury or accidents.When using this product, also read the “Precautions” described in the operatinginstructions for the camera to be attached.PrecautionsIn order to prevent injury, the product must be securely mounted to the mount bracket(locally procured) according to the Installation Guide of the camera.Mounting method for this productThis product is designed to be used as a pendant mount camera. If the product is mounted on adesktop or at a slant, it may not work correctly and its lifetime may be shortened.Make sure to remove this product if it will no longer be used.Precautions for installationOperating Instructions (this document) ................................................................................ 1 pc.Camera mounting screw (hexagon screw (M6)) ................................. 5 pcs.(of them, 1 for spare)Standard AccessoriesFor U.S. and Canada:Panasonic i-PRO Sensing SolutionsCorporation of America800 Gessner Rd, Suite 700 Houston, TX 77024https://www.security.us.panasonic.com/Panasonic Canada Inc.5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada1-877-495-0580https://www.panasonic.com/ca/© Panasonic i-PRO Sensing Solutions Co., Ltd. 2020For Europe and other countries:Panasonic Corporationhttp://www.panasonic.comPanasonic i-PRO Sensing Solutions Co., Ltd.Fukuoka, JapanAuthorised Representative in EU:Panasonic Testing CentrePanasonic Marketing Europe GmbHWinsbergring 15, 22525 Hamburg, GermanyFix the mount bracket (locally procured) on the installation surface.Pass the cables through the mount bracket andthis product.Fix a mount bracket to the installation surface byusing appropriate bolts, nuts or the like (locallyprocured).port for pullingout the cableHole for fixingmount bracketAttach the camera to this product.IMPORTANT:• For details on procedure for attaching mountbracket, read the operating instructions ofmount bracket.• After waterproofing the hole for fixing mountbracket and the port for pulling out the cableon the installation surface, fix the mountbracket on the installation surface.• Ensure the minimum pull-out strength thathas sufficient allowance for total mass ofmount bracket, this product, and camera etc.Mount bracket(locally procured)(Attachment image)Connect each cable to the camera, and attach the camera to this product with the cameramounting screw (accessory) or the hexagon screw supplied with the camera. Refer to theInstallation Guide of the camera for details such as the recommended tightening torque for thecamera mounting screws.InstallationThe following explains an example of mounting the camera on a ceiling.Prepare the mount bracket (locally procured) formounting the camera.ø58 mm {2-9/32 inches}85 mm{3-11/32 inches}Preparations before installationFix this product to the mount bracket (locally procured).Fix this product to the mount bracket.Fill the gap between the mount bracket and thisproduct with waterproof material (locally procured)such as silicon clay.This productMount bracket(locally procured)IMPORTANT:• The mount bracket (locally procured) shouldhave the configuration that enables fixation ofsafety wire from camera.R 1-1/2, 11crest,length MAX. 30 mm {1-3/16 inches}(taper pipe thread)RP 1-1/2, 11 crest,deep MAX. 30 mm {1-3/16 inches}(parallel pipe thread)Mount bracket(locally procured)This productWaterproof material(locally procured)Safety wireinstallationsurfacePanasonic i-PRO Sensing Solutions Co., Ltd. assumes no responsibility for injuries orproperty damage resulting from failures arising out of improper installation or operationinconsistent with this documentation.Caution:• Before attempting to connect or operate thisproduct, please read these instructions care-fully.Notice:• This product is not suitable for use in loca-tions where children are likely to be present.• Do not install this product in locations whereordinary persons can easily reach.• For information about screws and bracketsrequired for installation, refer to the corre-sponding section of this document.
