Panasonic WV-Q150C Operating Instructions Manual

Contents

operating instructions

Panasonic WV-Q150C Operating Instructions Manual Manual pdf 1 page image

InstallationsBe sure to read "Precautions" before installation. The Installation Guide of the network camera, WV-NS202, shall be read as well.1. Put the template (accessory) against the walland mark the positions of fixing screws andhole through which the cables run.If you run the cables through the wall, drill a holethrough the wall.2. Remove the bottom cover from this bracket.q Loosen the fixing screw (unremovable) to beused for cover fall prevention.w Pull down the bottom cover while pressingthe marks (shown with a in the drawing) toremove the cover.* Be aware that the inner shell is present inthe cover.Wall Mount BracketOperating InstructionsWV-Q150CModel Nos. WV-Q150SBefore attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.No model number suffix is shown in this manual.NM0806-1096 3TR004556BAA Printed in JapanPrefaceThis bracket is exclusively designed to mount the network camera, WV-NS202, on a wall.The network camera shall be mounted on this bracket after mounting this bracket on a concretewall.• WV-Q150C: Clear dome cover• WV-Q150S: Smoked dome cover (approx. 50 % of transmittance) Embedded box Strong panel ConcreteWall boxWallFixing screw to be used forcover fall preventionPrecautions• Refer installation work to the dealer.Installation work requires technique and experiences. Be sure to refer installation work to thedealer to avoid fire, electric shock, injury, or damage to the product.• Use only the specified camera.Failure to observe this may cause a fall of an inappropriate camera resulting in injury or acci-dents. Mount WV-NS202 on this bracket exclusively.• The measures of protection against a fall of the camera shall be taken.Failure to observe this may cause injury. Be sure to install this bracket-specific safety wire.• Avoid installing this bracket in the locations where salt damage occurs or corrosive gas isproduced.Otherwise, the mounting portions will deteriorate and accidents such as a fall of the camera mayoccur.• The screws and fixation mechanisms shall be tightened securely.Failure to observe this may cause a fall of the camera resulting in injury or accidents.• Periodic inspections shall be conducted.Rust on the metal parts or screws may cause a fall of the camera resulting in injury or accidents.Be sure to consult the dealer for the inspections.• Do not rub the edges of metal parts with your hand.Failure to observe this may cause injury.• Make sure that the installation area is strong enough to hold the total weight of the cameraassembly (approx. 1.8 kg {0.4 lbs.}) before installation.• The screws that secure this bracket on a wall are not supplied. Prepare the screws according tothe material, structure, strength and other factors of the mounting area and the total weight ofobjects to be mounted. (4 pieces of M4 screws or 2 pieces of M4 screws and 2 pieces of M6 orM8 anchor bolts) In this case, wood screws and nails should not be used.• Avoid installing in the following locations.• Locations where it may get wet from rain or water splash (not only outdoor)• Locations where a chemical agent is used such as a swimming pool• Locations subject to steam and oil smoke such as a kitchen• Locations near flammable gas or vapor• Locations where radiation or x-ray emissions are produced• Locations subject to strong magnetic field or radio waves• Locations where it may be damaged by briny air such as seashores• Locations where the temperature is not within –10 °C - +50 °C {14 °F - 122 °F}.• Locations subject to vibrations (This product is not designed for on-vehicle use.)• Locations where the temperature may rapidly change such as the peripheral areas of the airoutlets of air conditioners or doors facing outside. (In case of installing the camera in suchlocations, the dome cover may become foggy or condensation may be caused on the cover.)• The screws and bolts must be tightened with an appropriate tightening torque according to thematerial and strength of the installation area. After tightening the screws or bolts, perform visualcheck to ensure tightening is enough and there is no backlash.• The pull-out strength of the installation area shall be 40 N {4 kgf} or more per 1 screw.• The protection sheet attached to the dome cover shall be peeled off after installation.Major Operating Controls and Their Functions* If a microphone is used, mount the microphone on the rubber-made microphone stand. Unlessthe microphone is used, cut the rubber with a nipper or conduct another treatment.Installation AreaThe drawings below show how to conduct the wiring of this bracket.Template (accessory)Top coverBottom coverNotch for network cable, monitor out-put cable, etc.Hole for microphone cableNotch for network cableDome coverMicrophone stand*(To be continued reverse page)

/ 2

Related manuals for Panasonic WV-Q150C