Panasonic WV-Q152C Operating Instructions Manual

Also see for WV-Q152C: Operating instructions

Contents

operating instructions

Panasonic WV-Q152C Operating Instructions Manual Manual pdf 1 page image

Ceiling Mount BracketOperating InstructionsWV-Q152CModel Nos. WV-Q152SBefore attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.No model number suffix is shown in this manual.NM0806-1096 3TR004562BAA Printed in JapanPrefaceThis bracket is exclusively designed to mount the network camera, DG-NS202, on a wall.The network camera shall be mounted on this bracket after mounting this bracket on a ceiling.• WV-Q152C: Clear dome cover• WV-Q152S: Smoked dome cover (approx. 50 % of transmittance)Precautions• Refer installation work to the dealer.Installation work requires technique and experiences. Failure to observe this may cause fire,electric shock, injury, or damage to the product. Be sure to consult the dealer.• Use only the specified camera.Failure to observe this may cause a fall of an inappropriate camera resulting in injury or acci-dents. Mount WV-NS202 on this bracket exclusively.• Avoid installing this bracket in the locations where salt damage occurs or corrosive gas isproduced.Otherwise, the mounting portions will deteriorate and accidents such as a fall of the camera mayoccur.• The screws and fixation mechanisms shall be tightened securely.Failure to observe this may cause a fall of the camera resulting in injury.• Select an installation area that can support the total weight.If a selected area is too weak to support the total weight, a fall of the product may occur resultingin injury. Installation work shall be started after sufficient reinforcement.• Periodic inspections shall be conducted.Rust on the metal parts or screws may cause a fall of the product resulting in injury. Consult thedealer for the inspections.• The measures of protection against a fall of the camera shall be taken.Failure to observe this may cause injury. Be sure to install the safety wire.• Do not rub the edges of metal parts with your hand.Failure to observe this may cause injury.• Make sure that the installation area is strong enough to hold the total weight of the cameraassembly (approx. 1.2 kg {2.6 lbs.}) before installation.• The pull-out strength of the installation area shall be 196 N {20 kgf} or more per 1 screw. If a ceil-ing board such as plaster board is too weak to support the total weight, the area shall be suffi-ciently reinforced or the optional direct ceiling mount bracket for the camera, WV-Q105, shall beused.• Procure 4 screws (M4 or M6) securing the camera mounting bracket (supplied with the camera)according to the material of the installation area. In this case, wood screws and nails should notbe used.For mounting a camera on a concrete wall, use an anchor bolt (for M6) or an AY plug bolt (M4 orM6) manufactured by Matsushita Electric Works, Ltd. for securing.(Recommended tightening torque M4: 1.6 N·m {16 kgf·cm}, M6: 5.0 N·m {51 kgf·cm})• Avoid installing in the following locations.• Locations where it may get wet from rain or water splash (not only outdoor)• Locations where a chemical agent is used such as a swimming pool• Locations subject to steam and oil smoke such as a kitchen• Locations where radiation or x-ray emissions are produced• Locations where it may be damaged by briny air such as seashores• Locations where the temperature is not within –10 °C - +50 °C {14 °F- 122 °F}.• Locations subject to vibrations (This product is not designed for on-vehicle use.)• Locations where the temperature may rapidly change such as the peripheral areas of the airoutlets of air conditioners or doors facing outside. (In case of installing the camera in suchlocations, the dome cover may become foggy or condensation may be caused on the cover.)• The screws and bolts must be tightened with an appropriate tightening torque according to thematerial and strength of the installation area. After tightening the screws or bolts, perform visualcheck to ensure tightening is enough and there is no backlash.• The protection sheet attached to the dome cover shall be peeled off after installation.Major Operating Controls and Their Functions* If a microphone is used, mount the microphone on the rubber-made microphone stand. Unless themicrophone is used, cut the rubber with a nipper or conduct another treatment.LOCKOPENNotch for network cable, monitoroutput cable, etc.Dome coverCeiling mount bracketHole for microphone cableMicrophone stand*InstallationsBe sure to read "Precautions" before installation.The Installation Guide of the network camera, WV-NS202, shall be read as well.1. Install the inner shell.Slide the covers located on the both lateralsides of the camera and put the inner shell onthe camera until the hooks inside the inner shellare held in the holes of the camera (until a clickis heard).Important: Put the inner shell down on the cam-era until the outside cover of the cameracannot be seen from the opening (fromwhich the camera lens is visible) of the innershell. If this integration is not successfullyperformed, the inner shell may be removedor the hidden part at the top of the screenmay become larger in the WIDE mode.CoverHookPut on until a click is heardInner shellsHow to remove the inner shellPress the inner shell from the front and rearsides inward (at the same vertical positionas the hooks) to bend the shell and removethe shell from the camera.Press from the front and rearsides inward to bend(To be continued reverse page)Anchor bolt(Procured locally)Safety wire angle(WV-Q105 supplied)Safety wire(WV-Q105 supplied)Ceiling board such as plaster boardCeiling mount bracketInner shellDome coverMounting screws (4 pcs.)WV-Q105 supplied)WV-Q105 (option)

/ 2

Related manuals for Panasonic WV-Q152C