Panasonic WV-SC385 Installation Manual

Also see for WV-SC385: Integration note Product catalog Comparison chart Installation guide Operating instructions

Contents

Panasonic WV-SC385 Installation Manual Manual pdf 12 page image

Precautions for installationNo responsibility will be taken by our company withrespect to consequeces resulting from the use,damage or both of the camera.Installing placeContact your dealer for assistance if you are unsure of anappropriate place in your particular environment.• Make sure that the installation area is strong enoughto hold this product, such as a concrete ceiling.• When the installation area is not strong enough, rein-force and strengthen it or use an optional mountbracket (WV-Q155S, WV-Q155C, WV-Q156S,WV-Q156C or WV-Q105).• When the product is installed on a wall, use an option-al wall mount bracket (WV-Q154C).• When using an outdoor housing to install the product,use an optional inner cover (WV-Q157).• The optional mount brackets for WV-NS202A(WV-Q150C, WV-Q150S, WV-Q151C, WV-Q151S,WV-Q152C, WV-Q153) cannot be used with thisproduct.• When using an optional inner cover WV-Q157, upperside of images will be hidden (become black) whenthe tilt angle of the camera is almost level. (When"–5°" is selected for "Tilt Angle" on the setup menu,upper half of images will be hidden.) In this case,images may also be washed out depending on thephotographic subject when "On" is selected for"AGC" on the setup menu.Refer to the Operating Instructions (PDF) for furtherinformation about the setup menu.Do not place this product in the following places:• Locations where it may get wet from rain or watersplash• Locations where a chemical agent is used such as aswimming pool• Locations subject to humidity, dust, steam and oilsmoke• Locations in a specific environment where a solvent ora flammable atmosphere exists• Locations where a radiation, an X-ray, a strong radiowave or a strong magnetic field is generated• Locations where corrosive gas is produced, locationswhere it may be damaged by briny air such as sea-shores• Locations where the temperature is not within −10 °Cto +50 °C {14 °F to 122 °F}.• Locations subject to vibrations (This product is notdesigned for on-vehicle use.)• Locations subject to condensation as the result ofsevere changes in temperature (In case of installingthe camera in such locations, the dome cover maybecome foggy or condensation may be caused onthe cover.)Procure fixing screws separately.The screws that secure this product are not supplied.Prepare them according to the material and strength ofthe area where the product is to be installed.Screw tightening• The screws and bolts must be tightened with anappropriate tightening torque according to the materi-al and strength of the installation area.• Do not use an impact driver. Use of an impact drivermay damage the screws or cause tightening exces-sively.• When a screw is tightened, make the screw at a rightangle to the surface. After tightening the screws orbolts, perform visual check to ensure tightening isenough and there is no backlash.Be sure to remove this product if it is not in use.Radio disturbanceWhen this product is used near TV/radio antenna, strongelectric field or magnetic field (near a motor, a transformeror a power line), images may be distorted and noisesound may be produced.PoE (Power over Ethernet)Use a PoE hub/device that is compliant with IEEE802.3afstandard.RouterWhen connecting this product to the Internet, use abroadband router with the port forwarding function (NAT,IP masquerade).Refer to the Operating Instructions (PDF) for further infor-mation about the port forwarding function.Time & date settingIt is necessary to set the time & date before putting thisproduct into operation. Refer to the Operating Instructions(PDF) on the provided CD-ROM for descriptions of how toperform the settings.12