QERIDOO Sportrex1 User Manual
                   | |
30 – 02|2017 – Subject to change. Sportrex Sportrex Subject to change. – 02|2017 – 31Maintenance intervalsCaution!Replace corroded steel and aluminium parts immediately.Never bend back deformed or bent aluminium parts (risk of breakage). Replace bentaluminium parts immediately.Immediately replace plastic parts that have become porous or fragile due to theeffects of the weather, for example.Before every ride Check that the wheels are secure. The push-in axles must be engaged in the axle mount and itmust not be possible to pull them off without pressing the rubber cap. Check the air pressure in the wheels. It should be in the range of 2.75 – 4.5 bar. Check the air pressure of the buggy wheel (maximum air pressure: 2 bar). Check the total weight, including children and baggage. Check the fasteners of the cover and close them if necessary. Inspect all harnesses on the back and under the cabin to make sure that they are secure. Theymust be firmly tightened to hold the cover and backrest securely. Trailer mode: Make sure that the buggy wheel has been removed and that the requirementsdescribed in the chapter “Connecting the trailer to a bicycle” on page 26 have been fulfilled. Buggy mode: Make sure that the buggy wheel can rotate freely. Put the hand strap of the pushhandle around your wrist in order to prevent accidental rolling away. Walker mode: Make sure that the buggy wheel is secured facing straight ahead. Put the handstrap of the push handle around your wrist in order to prevent accidental rolling away. Check whether the tow bar, coupler and buggy wheel and their attachments are technicallyOK. Check that all screw and cotter pin connections are secure. Check the condition of the wheels. Replace covers and hoses in good time.Monthly (or every 200 km) Check the textile cover, all fasteners, the seats and the safety harnesses for cracks, wear andmissing parts. Inspect all frame tubes and all connecting pieces and fastening components for signs of wearand damage.Semi-annually (or every 500 km) Care for all sliding and moving parts with silicone spray. Clean the inside and outside of the cabin thoroughly.Every three years (or every 3000 km)Have a full inspection carried out by a specialist workshop no later than every three years.Care and maintenanceCare and maintenanceRegular care and maintenance of all parts and components helps prevent premature wear andkeeps the Sportrex ready for use at all times. This is particularly important when one of thefollowing influencing factors applies to your individual conditions of use: Frequent use with high mileage Regular use close to the maximum permitted total weight A sporty riding style (sudden starting and braking, cornering at speed etc.) Excessive weather influences such as UV radiation, temperature fluctuations, moisture, contactwith salt (sea water, salty air, road salt) Unfavourable storage conditions (lack of space, temperature fluctuations, sunlight)Caution!It is essential to adhere to the following care instructions and maintenance intervals.Perform the tests stated in the checklists conscientiously and at the specified times inorder to use the Sportrex in a technically safe condition.Replace damaged components immediately, see “Spare parts” on page 34. Ifnecessary, contact our service department or your local specialist dealer, see “Supportinformation” on page 33.CareCaution!For cleaning, use only water and domestic care agents such as detergents and textilecare products, soft cloths or impregnation and silicone spray. Do not use any sharp-edged tools or cleaning agents with a scouring effect. Cleaning agents containing acidsand solvents are also not permitted.After every use Clean the inside of the cabin. Pay attention to coarse dirt and remove it immediately if possible.After use in harsh weather conditions Clean the inside and outside of the cabin thoroughly. Care for all sliding or moving parts with silicone spray. Only fold up the cabin after it has been cleaned and is completely dry.When not in use Store the Sportrex only in places where the storage temperature falls within the range of -23 °Cto maximum 65 °C. The storage location should be dry, well ventilated and protected against direct sunlight. At higher storage temperatures, you should store the wheels separately from the cabinbecause the tyres’ rubber can cause odours. Use a Qeridoo folding garage if the Sportrex must be kept outdoors, see “Accessories” onpage 12. |
manualsdatabase
Your AI-powered manual search engine