Chapter 5: Templates 19Chapter 5: TemplatesInstrument edge Sun cover edgeDrill hole,9/32 in (7 mm)diameter in4 positionsUPRemovematerialfrom shadedarea onlyST70FLUSH MOUNTTemplate3.9 in (99 mm)4.1 in (104 mm)D10405-1

warnings and cautions

emc servicing and maintenance

product disposal

Chapter 1:Before you begin

Chapter 2:Planning

Positioning the ST70 instrument

Parts supplied

Parts not supplied

Chapter 3:Installation

Install transducers

Final fix

Chapter 4:Technical specifications

Chapter 5:Templates

surface mount

Raymarine ST70 Instrument Installation Manual

installation guide

emc installation guidelines

Product documents

Positioning the ST70 autopilot controller

seatalk systems

Commissioning

ST70 Instrument

safety notices

Introduction

Sail boat Pilot Controller keypad

Instrument keypad

Commonly used control functions

Setup principles

display types & grouping

Normal operation

user setup

Power boat functions

System information

Commissioning requirement

Requirement

Switch on

Setting Vessel Type

Setting date format

Setting time format

Data units

Leaving units setup

Dockside wizard

Rudder and motor checks for systems with a Rudder Reference transducer

Rudder and motor checks for systems without a Rudder Reference transducer

Hard over time

Depth offsets

Calibrating conventional transducers

Setting water temperature

Calibrating trim tabs

Setting magnetic variation

Changing display response rate

Rudder limit

Open water calibration

Starting open water calibration

Aligning the compass to GPS

AutoLearn

Next actions

Wind transducer setup

Alignment

Speed calibration for conventional speed transducer

Manual speed calibration

Speed calibration for smart transducer

Add point

Checking rudder gain

Rudder damping

General setup

Changing vessel type

Autopilot setup

Setting rudder gain

Setting turn rate limit

Setting rudder offset

AutoTurn

Additional sail boat settings

Gybe inhibit

System configuration

Maintenance

Cleaning

Using the display self-monitoring features

About Pilot

Appendix 1:Specifications

Pilot Controller (power boat) keypad

Appendix 2:Glossary

Index

product documents

Chapter 1:ST70 Overview

Display and controls

Operating principles

System functionality

Chapter 2:Setup Procedures

Dockside and open water procedures

Display settings

Autopilot calibration

Response Levels

Sailboat setup procedures

Wind Trim

Power boat and fishing boat setup procedures

SmartPilot Functions

Extended systems

Power and fishing boat menus

Pilot view

Using the SmartPilot to steer your boat

Using preset patterns

Activating Track mode

Leaving Track mode

Cross track error

Tidal stream compensation

Steering to the next waypoint in a route

Waypoint Advance warning

Using the SmartPilot with sail boats

WindTrim

Operating hints for Wind Vane mode

Chapter 4:Maintenance and troubleshooting

Troubleshooting

st70 pilot controller reference guide

Using the About Display feature

Technical support

telephone help line

Chapter 5:Alarms

Chapter 6:Data List

Chapter 7:Vessel Settings

Chapter 8:Technical specifications

warranty registration

display settings

technical accuracy

general information

power supplies

dedicated display power supply

parts supplied

parts not supplied

display power cables

seatalk ng connections

mounting procedure

installing transducers

smart transducers

autopilot calibration

initial setup

selecting language

select type

date & time

setting local time

changing units

initial setup end routine

hard over time

end of autopilot dockside setup

accessing transducer setup

calibrating conventional transducers

calibrating smart transducers

calibrating trim tabs

miscellaneous setup

changing display response rate

rudder limit

open water calibration

starting open water calibration

requirement for a clear area

instrument system calibration

wind transducer setup

speed calibration

speed calibration for conventional speed transducer

speed calibration for smart transducer

return to normal operation

checking rudder gain

emc conformance

all types

pilot controller (power boat) keypad

flush mount

Getting started

general operation

Display grouping & control

Setting display brightness

Setting the correct local time

Setting the screen colors

Choosing the data units

Setting up a Pilot Controller display

setting up data boxes

Basic autopilot operation

Using AutoTack

Using autopilot Track mode

Using autopilot Wind Vane mode

Using autopilot fishing patterns

Switching instrument pages on & off

Setting instrument page rollover

Changing information on a

Changing the page layout

Using alarm clock

Using race timers

Setting alarms

Alarm events

Chapter 1:ST70 General Information

Setup functions

Instruments not requiring commissioning

Day-to-day setting up

Power protocol

Chapter 2:Commissioning Procedures

Initial setup

Setting local time

Set water temperature

Set ground wind

Changing response rate

Ending dockside setup


Contents Table Of Contents warnings and cautions emc servicing and maintenance product disposal Chapter 1:Before you begin Chapter 2:Planning Positioning the ST70 instrument Parts supplied Parts not supplied Chapter 3:Installation Install transducers Final fix Chapter 4:Technical specifications Chapter 5:Templates surface mount	Chapter 5: Templates 19Chapter 5: TemplatesInstrument edge Sun cover edgeDrill hole,9/32 in (7 mm)diameter in4 positionsUPRemovematerialfrom shadedarea onlyST70FLUSH MOUNTTemplate3.9 in (99 mm)4.1 in (104 mm)D10405-1 Previous Next / 28