Raypak RAYTHERM 0133-4001 Installation And Operating Instructions Manual

Also see for 0133-4001: Installation and operating instructions

Raypak RAYTHERM 0133-4001 Installation And Operating Instructions Manual Manual pdf 27 page image

LIGHTING INSTRUCTIONS FOR BOILERS WITH ELECTRONIC IGNITION (IID)For Models with Manual Gas ValvesFOR YOUR SAFETY READ BEFORE OPERATINGWARNING: If you do not follow these instructions exactly, a fire or explosion may result causingproperty damage, personal injury or loss of life.A. This appliance is equipped with an ignition device whichautomatically lights the pilot. Do not try to light the pilotby hand.B. BEFORE OPERATING smell all around the appliancearea for gas. Be sure to smell next to the floor becausesome gas is heavier than air and will settle on the floor.WHAT TO DO IF YOU SMELL GAS* Do not try to light any appliance.* Do not touch any electric switch; do not use any phonein your building.* Immediately call your gas supplier from your neighborísphone. Follow the gas supplierís instructions.* If you cannot reach your gas supplier, call the fire de-partment.C. Use only your hand to push in or turn the gas controlknob. Never use tools. If the knob will not push in or turnby hand, do not try to repair it, call a qualified servicetechnician. Force or attempted repair may result in a fireor explosion.D. Do not use this appliance if any part has been underwater. Immediately call a qualified service technician toinspect the appliance and to replace any part of thecontrol system and any gas control which has beenunder water.OPERATING INSTRUCTIONSFor Honeywell gas valve: Turn gas control knobcounter-clockwise from ìOFFî until itstops. Push in gas control knob and continuerotating counter-clockwise to ìONîposition. Make sure knob rests against stop.For Honeywell gas valve (Models 40# only):Turn gas control knob counter-clockwise to ìONî.9. Replace boiler door panel.10. Turn on all electrical power to the appliance.11. Set thermostat to desired setting.12. If the appliance will not operate, follow the instructionsìTo Turn Off Gas To Applianceî and call your servicetechnician or gas supplier.HONEYWELLGAS CONTROLKNOB SHOWNIN "ON" POSITIONGAS INLETROBERTSHAWGAS CONTROLKNOB SHOWNIN "ON" POSITIONGAS INLETFig. # 8080TO TURN OFF GAS TO APPLIANCE1. Set the thermostat to the lowest setting.2. Turn off all the electrical power to the appliance if serviceis to be performed.3. Remove door panel.4. For Robertshaw gas valve: Turn gas control knobclockwise to ìOFFî.For Honeywell gas valve (all models except 40#):Turn gas control knob clock-wise to ìOFFî.Make sure knob rests against stop.For Honeywell gas valve (Models 40# only):Push in gas control knob slightly and turn clockwiseto ìOFFî.5. Replace heater door panel.Fig. #8219GAS CONTROL KNOBSHOWN IN "ON"POSITIONGAS INLETFig. # 80821. STOP! Read the safety information above.2. Set the thermostat on the lowest setting.3. Turn off all electrical power to the appliance.4. This appliance is equipped with an ignition device whichautomatically lights the pilot. Do not try to light the pilotby hand.5. Remove boiler door panel.6. For Robertshaw gas valve: Turn gas control knobclockwise to ìOFFî.For Honeywell gas valve (all models except 40#):Turn gas control knob clockwise to ìOFF".Make sure knob rest against stop.For Honeywell gas valve (Models 40# only):Push in gas control knob slightly and turn clockwiseto ìOFFî. Knob cannot be turned to ìOFFîunless knob is pushed in slightly. Do not force.7. Wait five (5) minutes to clear out any gas. Then smellfor gas, including near the floor. If you smell gas, STOP!Follow ìBî in the safety information above. Ifyou do not smell gas, go to the next step.8. For Robertshaw gas valve: Turn gas control knobcounter-clockwise to ìONî.27