Saeco Moltio HD8768 AMF Manual

Contents

Confidential Divison, MMMM dd, yyyy, ReferenceError message (E01/E03/E04/E05/E14)E01: Take out the brew group and unblock/clean the coffee duct outlet (coffee funnel). Clean and re-grease the brew group before placing it back.E03/E04: Clean and re-grease the brew group. Make sure the brew group is in rest position before placing it back.E05: 1). Try to prime the machine by dispensing some hot water. 2.) The steam wand is clogged with dirt, clean it with a pin. 3). When using an extra water filter, remove this filterfrom the water tank and turn the machine OFF and back ON. 4). Take out and place back the water tank a few times.E14: Switch OFF the machine and let it cool down for one hour.Alarm message “Fill bean container” appears, but the bean container is filled with coffee beans: This is caused by a dirty/greasy coffee bean container. If it is greasy the beansdo not glide into the grinder anymore. To solve the problem: Remove the coffee bean container and disassemble it. Clean both parts with a cloth, reattach the parts andplace the coffee bean container back into the machine. Also clean the area under the coffee bean container with a cloth.Alarm message “Change filter” does not disappear, but the filter has been changed: 1. The new filter has to be confirmed in the machine menu. Enter Menu -> select Setting ->select Water -> select Activate filter and follow the steps in the display. 2). If you do not want to use a filter anymore choose “Enable filter”.Alarm message “Empty coffee ground container” does not disappear, but the container has been emptied: Always empty the container when the machine is switched ONand when the empty symbol appears. Otherwise the machine does not register it is emptied.Alarm message “Insert bean container “ does not disappear, but the bean container is inserted: Coffee beans, coffee residues or dirt are present underneath or inside thecoffee bean container. The symbol may also stay on the display if the coffee bean container is not placed properly. An incorrectly placed container lid can also cause thisproblem. Always make sure that the selector is in the lock position "".Cannot finish the descaling procedure as the machine keeps asking to insert the drip tray: 1. Make sure that the drip tray is clean and dry. Especially clean the small corner atthe back of the drip tray. If this is not clean the sensor cannot register that the drip tray is placed back.There is water under the machine (machine is leaking): This can have different causes; 1. The drip tray is too full and overflowed during brewing or the descaling process. Alwayscheck the ’drip tray full’ indicator before brewing a coffee and empty the drip tray before you start descaling. 2. Check if the water tank is leaking. 3. The brew group or thedrains may be blocked, clean the brew group and the inside of the machine.Cannot insert/remove the brew group:Cannot insert: 1). Make sure the brew group is set in the rest position before placing it back. 2.) If still not possible to insert; place back the drip tray including coffee groundcontainer, close service door, switch ON and back OFF the machine. Try again to insert the brew group.Cannot remove: 1). Check if the machine is still in the descaling process, if yes then first finish the descaling. If not, place back the drip tray including coffee ground container,close service door, switch ON and back OFF the machine. Try again to remove the brew group.The drip tray fills up quite fast: It is normal for the drip tray to fill up quickly. During use, the internal circuits are rinsed with water that automatically ends up in the drip tray.The machine is not grinding the beans: 1. The bean container is dirty or coffee beans are stuck in between the two parts. Remove the coffee bean container and disassembleit. Clean both parts with a cloth, reattach the parts and place the coffee bean container back into the machine. Also clean the area under the coffee bean container with acloth. 2. Change the grind setting to a courser setting. 3. Clean the coffee duct outlet and brew group.The coffee pucks are wet, and/or there is water in the coffee ground container: The consistency of the coffee pucks is related to the settings of the machine, and does notdirectly point to a machine defect. Expect watery coffee pucks or some extra water in the coffee ground container: 1. During first time use as auto-dosing system is stilladapting. 2. After switching to a different blend of coffee beans or adjusting the grind settings, just brew some extra cups. 3. After changing machine settings as; grind setting,coffee volume and aroma setting. As a coarse grind setting, higher coffee volume or a lighter aroma setting will lead to a waterier coffee puck.The coffee/milk temperature is not hot enough: 1. Adjust the “temperature” in the machine menu, select temperature. The settings are HIGH/NORMAL/LOW. 2. Pre-heat thecups and use thin walled cups . 3. Adding cold milk or warm frothed milk, in both cases the temperature will decrease to some extent. Milk foam in particular should not beheated up to more than 55°C.No coffee or only some drops of coffee are being dispensed (not first time use)/ The coffee is getting watery: This can have different causes; 1). Blocked grinder, clean thecoffee bean container and coffee duct. 2). Polluted/not well greased brew group; clean the brew group and make sure all parts are well greased. 3). Grind setting is set toofine. Change the grinder to a course setting. 4). Extra water filter not well placed (optional). Remove the extra water filter and try to make a coffee. Make sure the filter is wellplaced or replace the filter. 5). Lime scale is causing a blockage. Descale the machine.Trouble shoot:

/ 3

Related manuals for Saeco Moltio HD8768 AMF