34 EnglishAdvanced FeaturesNetwork Setup (Manual)If the other methods do not work, you need to enter theNetwork setting values manually.Getting the Network Connection ValuesTo get the Network connection values on most Windowscomputers, follow these steps:1. Right click the Network icon on the bottom right of thescreen.2. In the pop-up menu, click Status.3. On the dialog that appears, click the Support tab.4. On the Support tab, click the Details button. TheNetwork settings are displayed.How to set up manuallyTo enter the Network connection values manually, followthese steps:1. Follow Steps 1 through 6 in the “How to set up usingPBC (WPS)” (p. 32).2. Press the ▼ button to select Internet Protocol Setup,and then press the ENTERE button. Press the ▲or ▼ button to select Manual, and then press theENTERE button.3. Press the ▼ button to go to the first entry field (IPAddress).4. Use the number buttons to enter numbers.5. When done with each field, use the ► button to movesuccessively to the next field. You can also use the otherarrow buttons to move up, down, and back.6. Enter the IP Address, Subnet Mask, and Gatewayvalues.7. Press the ▲ or ▼ button to go to DNS.8. Press the ▼ button to go to the first DNS entry field.Enter the numbers as above.9. When done, press the ▲ button to go to Select aNetwork. Select your network, and then press theENTERE button.10. Go to Step 4 in the “How to set up automatically” (p.32), and follow the directions from that point on.SWL (Samsung Wireless Link)This function lets you connect a Samsung device thatsupports the PBC (WPS) to your TV. You can connectdevices to the TV even if a sharer is not connected to the TV.✎ To use the Internet@TV, the AP (access point) must beconnected to the wireless network.✎ If a Samsung Wireless Lan Adaptor is connected to theUSB 2 port, the network may not operate normally. Werecommend to connecting it to the USB 1 (HDD) port.✎ Only sharers using the 2.4 Ghz band are supported.Sharers using the 5 Ghz band are not supported.SWL connectYou can directly connect a device that supports the PBC(WPS) to the TV.✎ This function is available when SWL (SamsungWireless Link) is set to On.How to connect Samsung Wireless LinkFor the procedures to establish a connection, refer to thefollowing:1. Follow Steps 1 through 5 in the “How to set up usingPBC (WPS)” (p. 32).2. Select Samsung Wireless Link by using the ▼ buttonand press the ENTERE button to turn it On.3. Select SWL connect by using the ▼ button and pressthe ENTERE button.4. If the “Press the PBC button on the device whichsupports PBC button to connect within 120seconds” message appears, press the PBC button onthe device to connect.✎ For more information, refer to the wireless networksetup manual of the device to be connected.5. If the device is connected properly to the TV afterstarting count on message box then message box willbe disappeared automatically.✎ If the connection fails, please retry after 2 minutes.If Your TV Fails to Connect to the InternetYour TV may not be able to connect to the Internetbecause your ISP has permanently registered theMAC address (a unique identifying number) of yourPC or modem, which it then authenticates each timeyou connect to the Internet as a way of preventingunauthorized access. As your TV has a different MACaddress, your ISP can not authenticate its MAC address,and your TV can not connect.To resolve this problem, ask your ISP about theprocedures required to connect devices other than a PC(such as your TV) to the Internet.If your Internet service provider requires an ID or passwordto connect to the Internet, your TV may not be able toconnect to the Internet. If this is the case, you must enteryour ID or password when connecting to the Internet.The internet connection may fail because of a firewallproblem. If this is the case, contact your Internet serviceprovider.If you cannot connect to the Internet even after you havefollowed the procedures of your Internet service provider,please contact Samsung Electronics at 1-800-SAMSUNG.