Samsung LN32C550 User Manual

Also see for LN37C550: User manual User manual Quick setup guide User manual User manual

Contents

38 EnglishAdvanced Featureslistening through a Receiver¦You can listen to sound through a receiver (i.e Home Theater) instead of the TV speaker.1. Select Receiver and set to On.2. Press the EXIT button to exit.If your receiver supports audio only, it may not appear in the device list.✎The receiver will work when you have properly connected the optical in jack of the receiver to the✎ DIgITAl AUDIOOUT (OPTICAl) jack of the TV.When the receiver (i.e Home Theater) is set to✎ On, you can hear sound output from the TV’s Optical jack. Whenthe TV is displaying a DTV (air) signal, the TV will send out 5.1 channel sound to the receiver. When the source is adigital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard fromthe receiver.nOTE✎You can only control Anynet+ devices using the TV remote control, not the buttons on the TV.xThe TV remote control may not work under certain conditions. If this occurs, reselect the Anynet+ device.xThe Anynet+ functions do not operate with other manufacturers’ products.xTroubleshooting for Anynet+¦Problem Possible solutionAnynet+ does not work. Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.•Only one receiver (home theater) can be connected.•Check if the Anynet+ device power cord is properly connected.•Check the Anynet+ device’s Video/Audio/HDMI cable connections.•Check whether• Anynet+ (hDMI-CEC) is set to On in the Anynet+ setup menu.Check whether the TV remote control is in TV mode.•Check whether the remote control is Anynet+ compatible.•Anynet+ does not work in certain situations. (Searching channels, operating• Media Play or Plug & Play(initial setup), etc.)When connecting or removing the HDMI cable, please make sure to search devices again or turn your•TV off and on again.Check if the Anynet+ Function of Anynet+ device is set on.•I want to start Anynet+. Check if the Anynet+ device is properly connected to the TV and check if the• Anynet+ (hDMI-CEC) isset to On in the Anynet+ Setup menu.Press the• TOOls button to display the Anynet+ menu and select a menu you want.I want to exit Anynet+. Select• View TV in the Anynet+ menu.Press the• sOURCE button on the TV remote control and select a device other than Anynet+ devices.Press• > Ch <, Ch lIsT, PRE-Ch, and FAV.Ch to change the TV mode. (Note that the channelbutton operates only when a tuner-embedded Anynet+ device is not connected.)The message ‘Connecting toAnynet+ device...’ appears onthe screen.You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.•Use the remote control when the Anynet+ setting or switching to view mode is complete.•The Anynet+ device does notplay.You cannot use the play function when• Plug & Play (initial setup) is in progress.The connected device is notdisplayed.Check whether or not the device supports Anynet+ functions.•Check whether or not the HDMI cable is properly connected.•Check whether• Anynet+ (hDMI-CEC) is set to On in the Anynet+ setup menu.Search Anynet+ devices again.•You can connect an Anynet+ device using the HDMI cable only. Some HDMI cables may not support•Anynet+ functions.If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power cord or a•power failure, please repeat the device scan.The TV Program cannot berecorded.Check whether the antenna jack on the recording device is properly connected.•The TV sound is not outputthrough the receiver.Connect the optical cable between TV and the receiver.•