Samsung PS50A476P1D User Manual
Also see for PS50A476: User manual
                                                           | |
Contents
|
English - 1 Connect a HDMI/DVI cable between the HDMI IN 2 jack on the TV and the PC output jack on yourcomputer. Connect a 3.5mm Stereo/2RCA cable between the DVI IN (HDMI 2) [R-AUDIO-L] jack on the TV andthe Audio Out jack of the sound card on your computer. Connect the Emitter to the 3D SYNC OUT port on the rear panel of the TV.4 Turn the TV on and set the source of the TV to HDMI2. For more information on the 3D glasses (including the Emitter), refer to the user manual of your 3Dglasses. Adjust the PC resolution: PS50A476: 1024 x 768@60Hz,1360 x 768@60Hz Optimum PC resolution for PS50A476 is 1360x768. When 1024x768 signal is connected in 3D mode,the picture will be shown in 4:3 format with left and right side grey bars appeared. The 3D IR Emitter communicates with the 3D glasses.Therefore, the 3D IR Emitter should be located near the 3D glasses. It is activated when the HDMI or DVI input signal is RGB, and DVI Sound is supported. When the power is turned on or off, the mode changes to the default (Off) and the Format is saved. The D Effect is turned on or off regardless of the Picture Mode. When D Effect is on, only the Contrast, Brightness, D Effect, and Reset picture menus areactivated. To use the 3D Effect function, a graphics card supporting 3D or 3D software is required. The 3D glasses and the Emitter must be manufacturer by the same company. If you play a game or watch TV while wearing the 3D glasses for long periods of time, you mayexperience eyestrain or a headache. 3D glasses (including the Emitter) not manufactured by Samsung may not be supported. If you find the screen flickering while the 3D function is used, change the environmental lightingdarker or turn off the fluorescent lamp to watch the screen for its best condition.Changing the ModeChanging the Mode will exchange the pictures for each eye byexchanging the left and right output signals.1 Connect the TV, PC and 3D IR Emitter as shown in the figure.2 Press the SOURCE button to select HDMI .3 Press the MENU button to display the menu.Press the ▲ or ▼ button to select Picture, then press theENTER button.4 Press the ▲ or ▼ button to select Picture Option then pressthe ENTER button.Press the ▲ or ▼ button to select D Effect then press theENTER button.5 Press the ▲ or ▼ button to select Mode, then press theENTER button.Press the ▲ or ▼ button to select Off, Mode1, Mode or DConversion then press the ENTER button.• Off : Turns the 3D Effect function off.• Mode1 : Mode 1 operates with right sync first.• Mode : Mode 2 operates with left sync first.• D Conversion : Provides picture converted 3D to 2D. You can choose this to watch 2D picture temporally when you feeldizzy, but you should choose “Off” to end 3D Effect completely. If the 3D effect is not working properly, it means the Mode and3D glasses may not be syncing properly. To put them in sync,switch to the other mode. Continued...Move Enter ReturnMode : Standard Cell Light Contrast 0Brightness 45Sharpness 50Colour 50Tint G50 R50Detailed Settings Picture Options Reset : OK PictureT VMove Enter ReturnColour Tone : Normal Size : Auto Wide Screen Mode : 1: Digital NR : Auto Real 100 Hz Demo : Off DNle : Off HDMI Black Level : Normal Blue only mode : Off Screen Burn Protection D Effect Picture OptionsT VMove Enter ReturnMode :Format :D EffectT VOffMode1ModeD Conversion |
Related manuals for Samsung PS50A476
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine