Samsung RL37SGPS Instruction Manual

Also see for RL34EC series: Instruction manual

Contents

4Changing the direction of the door opening(RL34EG*,RL37EG*)Safety PrecautionsWhen comparing the appliance with other refrigerators, please refer to the model andnumber;Before the appliance is connected to the power, verify if voltage rating of the refrigerator issame to the power voltage. The voltage can be variable from 187V to 240V; if the powervoltage can not meet the requirements, an automatic transformer with a minimum output of500W shall be used.If the appliance is disconnected from the power, you should wait for at least five minutesbefore reconnection; otherwise there may be a hazard to the compressor.Do not store food close to the temperature sensor; otherwise it may display wrongtemperatures.Do not open and close the door too frequently or for a long time during hot weather;otherwise it may affect the efficiency of the entire unit and burden the appliance withexcessive load.Do not leave the refrigerator upside down or horizontal or keep inclined over 45 degree tothe ground if necessary;Do not pull or push the appliance by holding the door handles or exert too much upward/downward forces on the door handle;If a lot of hot foods are stored at the same time or the door is opened frequently or kept openfor a long period of time, the internal temperature will rise and the temperature display mayflash. It will be recovered normal after a period of stable operation;The refrigerator must be located with an easy access to the power supply.¡ô¡ô¡ô¡ô¡ô¡ô¡ô¡ô¡ô1.Remove all the packing materials of the components,and do remove the foam pad under the refrigeratorduring the operation;2.Clean the interior and exterior of the refrigerator withwet warm cloth (add little neutral detergent in the warmwater).3.The power plug can be connected around one hour after therefrigerator is positioned stable, please make the appropriateoperations with careful reference to the page of control panelintroduction.Preparing the appliance for useCautionThe cooling effects originates from refrigerant that is filled throughspecial process. Please ensure the pipes in the rear are intact.AlertThis appliance adopts R600a refrigerant which is combustible.During transportation and installation, please handle the appliance carefullyto protect the cooling system from damage.- To avoid the combustible gas composed of the refrigerant leaked from the cooling circuit and the air,please select the room size to accommodate t he appliance according to the refrigerant quantity.The room size shall be calculated as per the criterion of 8g R600a per square metres.For details of the refrigerant quantity, please refer to the manual.- Do not start the appliance that has any damage. If any problems, please contact the dealer orservice centre.The refrigerant leaked from the pipe may catch fire or hurt your eyes. If refrigerant leakage occurs,please keep away the fire or potential fire source, and keep the room aired for several minutes.131. Take down the SCREW B which is fixing the COVER TOPFRONT and then COVER TOP FRONT. Pull out the wire inserts.Take down COVERHINGE UPP R SCREW A HINGE UPP RCOVER DOOR UPP and fridge door.Take down and fix SHAFT-HINGEto the opposite side of HINGE UPP.Take down CAP HOLE TOP atCOVER TOP FRONT and install it on the right of COVER TOP FRONT.2. Take down SCREW A, SCREW E and MID HINGE of the fixing hinge and then freezer door.Take down CAP HINGE HOLE, CAP SCREW CABI and SCREW F at left and install them at right.3. Gently incline the appliance in less than 45 degree, remove the right FOOT and unfastenSCREW D. Take down right HINGE LOW. Then take down FIX HINGE LOW,SHIFT HINGEand STOPPER HINGE LOW.Reverse STOPPER HINGE LOW and fix it to the left ofHINGE LOW with FIXER HINGE LOW andSHIFT HINGE.4. Take down the left FOOT and unfasten SCREW D.Take down and fix REINF to the right. Then fix FOOT.5. Take off the SCREW G and STOPPERDOOR in the freezer door and install them at the leftof the door.Take off CAP HOLEDOOR, CAP SCREW HANDLE, SCREW C, ASSY HANDLE BAR,and CAP SPACER DOOR, and install them at the right of the door.Install CAP HOLEDOOR on the left of the door.6. Fix MID HINGE with SCREW A and SCREW E, and install the freezer door Fix HINGE-LOW to theleft and install FOOT.Put the refrigerator stable and install the fridge door.Fix HINGE UPP with SCREW A.7. Fix the wire inserts properly.Install COVER HINGE UPP L and cover it with COVER DOOR UPP.8. Install COVER TOP FRONT and finally fasten SCREW B.COVER TOP FRONTCAP SCREW CABICAP HINGE HOLEMID HINGEREINFSCREW DFOOT HINGE LOWCAP HANDLESCREW AHINGE UPP RFOOTSCREW BCAP SPACER DOORCOVER TOP UPPCAP HOLE DOORSTOPPER DOORSTOPPER DOORCAP HOLE DOORSTOPPER HINGE LOWFIXER HINGE LOWCOVER HINGE UPP LCOVER HINGE UPP RCAP SCREW HANDLESCREW ASCREW ESCREW CCAP SCREW HANDLESCREW CSCREW DSCREW FCAP HINGE HOLESCREW GSCREW GSHAFT-HINGECAP HOLE TOPSHAFT HINGEAdvance Type: