Samsung SV-DVD3E Instruction Manual

Also see for SV-DVD3E: Instruction manual Instruction manual Service manual Service manual

Contents

GB33GB32Modifying ShowView ProgrammingUsing the ShowView FeatureBefore presetting your DVD-VCR: Switch on both the television and your DVD-VCR Check that the date and time are correct Insert the cassette on which the programme is to berecorded (safety tab intact)Up to six programmes can be preset.1 To enter a ShowView, press the TIMER button.Press the ❷!and ENTER buttons to select SHOWVIEW.Result: A message is displayed to allow you to enter theShowView code.☛ If all six programmes have been set, the message TIMERIS FULL is displayed. Refer to page 35 if you wish tocancel a preset recording.2 Press the numeric buttons to enter the code opposite theprogramme that you wish to record in your television magazine.➢ If you wish to correct the ShowView code that you areentering: Press the ➛ button until the digit to be corrected iscleared Enter the correct digit3 Press the ENTER button.Result: The information concerning the programme is displayed.☛ When using the ShowView function for the first time withstored stations, the programme number flashes. This onetime, you must enter the station number manually bypressing the " or ❷ buttons. Refer to the following page if: The programme number or times flash You wish to modify the programme4 If the programme and times are correct, press the RETURN button.5 Press the STANDBY/ON button to activate the timer.6 Refer to page 35 if you wish to: Check that your DVD-VCR has been programmed correctly Cancel a preset recording☛ The numbers next to each TV programme listing areSHOWVIEW code numbers, which allow you toprogramme your videorecorder instantly with the remotecontrol. Tap in the ShowView code for the programmeyou wish to record.™ ShowView is a trademark of Gemstar Development Corporation. The ShowView system ismanufactured under licence from Gemstar Development Corporation.SETUP/ENTERRETURN TITLE SUBTITLE MARKA.DUB SPEED TIMER INDEX2 34 5 67 8 9SHUTTLESTANDBY/ON OPEN/CLOSEAUDIOMODE/REPEATTV/VCRCLOCK/COUNTER5SHOWVIEWCODE ---------CODE:0-9 CORRECT:➛RETURN ENTER1/JAN TUE 12:09PR DAY START→STOP V/P-- ---- --:--→--:---- --- ---- --:--→--:---- --- ---- --:--→--:---- --- ---- --:--→--:---- --- ---- --:--→--:---- --- ---- --:--→--:---- -"❷ SET:❿RETURN DELETE:CLEAR1TIMER METHODSTANDARDSHOWVIEWRETURN "❷ ENTERIf you wish to correct the programme displayed or modify certain elements, such as the recording speed,you can do so before you press SETUP a second time to confirm.If you wish to... Then...Select an input source other Press the ➛ or ❿ buttons, until the PR selection flashes.than the tuner (AV1, AV2 or AUX) Press the INPUT SEL. button one or more times to change theinput source selection.Result: The programme number is replaced by:• The AV1, AV2 or AUX source using the INPUTSEL. button for a satellite tuner or external videosource➢ The input source must be selected before changing anyother value.Record a programme every day Press the ➛ or ❿ buttons, until the DAY selection flashes.(Monday to Sunday) at the same time Press the " or ❷ buttons, until the DLY (Daily) value isdisplayed.Record a programme every week Press the ➛ or ❿ buttons, until the DAY selection flashes.on the same day and at the same time Press the " or ❷ buttons, until the W- (Week) value isdisplayed, followed by the required day.Example: W-SA (Weekly Saturday)Extend the recording time Press the ➛ or ❿ buttons, until the STOP selection flashes. Press the " or ❷ buttons to increase or decrease the stoptime.Select the recording speed Press the ➛ or ❿ buttons, until the recording speed selectionflashes. Press the " or ❷ buttons until the correct indication isdisplayed:• AUTO (Auto Tape Speed Select) : see page 34• SP (Standard Play)• LP (Long Play)Select the PDC recording Press the ➛ or ❿ buttons, until the V/P selection flashes. Press the " or ❷ buttons until the “ON” indication is displayed.☛ Do not select PDC unless you are sure the programme youwish to record is broadcast with PDC. If you do set PDC ON(by selecting “ON” in the right - hand column on the screen),then you must set up the start-time EXACTLY according tothe published TV schedule. Otherwise the timer recordingwon’t take place.VCRVCR