Sanyo PLC-XU101 Service Manual

Also see for PLC-XU101: Owner's manual

Contents

-33-Electrical AdjustmentsGroup/Item Item Name Function Initial Range Note162 PreCoast YCbCr 1080i 60Hz 7 0 - 63163 PostCoast YCbCr 1080i 60Hz 13 0 - 63164 PreCoast YCbCr 1080i 50Hz 7 0 - 63165 PostCoast YCbCr 1080i 50Hz 13 0 - 63166 PreCoast YCbCr 1035i 7 0 - 63167 PostCoast YCbCr 1035i 13 0 - 63180 PreCoast SCART 480i 7 0 - 63181 PostCoast SCART 480i 13 0 - 63182 PreCoast SCART 575i 7 0 - 63183 PostCoast SCART 575i 13 0 - 63Group 10 Sync Processor0 SYNCAMPHLCKTOLOW Minimum sync amplitude threshold for HLCK1 to 0 tansition 0x1000 0 - 99991 SYNCAMPHLCKTOHI Minimum sync amplitude threshold for HLCK0 to 1 tansition 0x700 0 - 9999Group 20 Video Decoder *R : Read Only Value0 Y Level Composite / S-Video - Y Level (ADC RGBGain) 10 / 10 0 - 255 Composite / S-Video* Gain Adjustment [Video]1 C Level Composite / S-Video - C Level (ADCSaturation) 115 / 115 0 - 255 Composite / S-Video23 XCXL Level Cross-Chroma, Cross-Luma Level 3 0 - 54 C2DNBANDWIDTH Comb 2D Narrow Bandwidth 3 / 3 0 - 3 NTSC/PAL5 C2DWBANDWIDTH Comb 2D Wide Bandwidth 4 / 4 0 - 7 NTSC/PAL6 C2DCNMINLEAK Comb 2D Chroma Narrow Band MinimumLeakage 0 / 3 0 - 3 Left Values are adjustable if CXCL Level = 5.7 C2DCNSLOPELEAK Comb 2D Narrow Band Slope Leakage 7 / 7 0 - 7 NTSC/PAL8 C2DCWMINLEAK Comb 2D Wide Band Minimum Leakage 1 / 3 0 - 3 NTSC/PAL9 C2DCWSLOPELEAK Comb 2D CW Slope Leakage 6 / 6 0 - 7 NTSC/PAL10 COMBLEAK2BPGAIN Comb Leak To Ban Pass Gain 1 / 0 0 - 3 NTSC/PAL11 C2DBDIAGONALGAIN Comb 2D Band Pass Diagonal Gain 1 / 3 0 - 3 NTSC/PAL12 C2DNBCWBCLGAIN Comb 2D Narrow Band Comb Wide BandComb 1 / 1 0 - 3 NTSC/PAL13 RLUMASETUP-Enable 7.5IRE Setup Enable 0 0 - 1 Effective only NTSC SignalGroup 40 General0 IP Mode Sets for IP Off 1 0 - 1 0: IP Block not used1: IP OFF used with IP Block1 3:2 PullDown Mode 1 1 - 3 bit0 : Global Motionbit1 : Video Motion2 Detect Film Mode Enable 0 0 - 2 0 : 2:3pull down & 2:2pull down1 : 2:3pull down2 : 2:2pull down3 Force IP Mode 2 0 - 20 : IP Process Disable1 : Force Normal IP Mode2 : Force Film ModeEffective only for PSF Signal.Group 41 Deinterlacer setting Effective only for Progressive ON-L1 mode.0 Motion Adaptive Weight Value 60 0 - 2551 Angle Interpolation Level 0 : Conservative <====> 4 : Aggressive 4 0 - 42 CUE Low Pass Filter Enable 0 0 - 1Group 42 Deinterlacer setting Effective only for Progressive ON-L2 mode.0 Motion Adaptive Weight Value 0 0 - 2551 Angle Interpolation Level 0 : Conservative <====> 4 : Aggressive 2 0 - 42 CUE Low Pass Filter Enable 0 0 - 1Group 43 Deinterlacer setting Effective only for Progressive ON/Film mode.0 Motion Adaptive Weight Value 30 0 - 2551 Angle Interpolation Level 0 : Conservative <====> 4 : Aggressive 4 0 - 42 CUE Low Pass Filter Enable 0 0 - 1Group 45 Noise Reduction (Time) Effective only for N.R - Off0 Noise Pixel Range / 1 0 - 21 Noise Region 0 / 12 0 - 10232 Noise Region 1 / 24 0 - 10233 Noise Region 2 / 40 0 - 10234 Noise Gain Level / 0 0 - 255