Sanyo VDC-C1574VA - CCTV Camera Instruction Manual

Also see for VDC-C1574VA - CCTV Camera: Specifications Specifications

Contents

Sanyo VDC-C1574VA - CCTV Camera Instruction Manual Manual pdf 2 page image

J CHECKING THE CAMERA IMAGEYou can use the monitor checking cable (sold separately) todisplay an image on a monitor when setting up the camera to checkthe surveillance angle and range, lens focus, etc.Connect the connector of the monitor checking cable to the monitorchecking connector (a) on the circuit board and connect the jackof the monitor checking cable to the monitor.J LENS ADJUSTMENTSOnce the camera has been installed, adjust the lens section.Be careful not to touch the lens section when changing the angleof the camera.When loosening the drop-prevention cord fixing screw, becareful not to loosen it too much; otherwise the dome cover maydrop.1 Loosen the drop-prevention cord fixing screw, then adjust the panposition (±180°) and the tilt position (±60°).Loosen the screw (A) with a Phillips head screwdriver beforeadjusting the tilt position.2 Loosen the zoom lever screw, turn the zoom lever to the right/left to determine the zoom position while viewing the cameraimages on the monitor, and then re-tighten the screw.3 Loosen the focus lever screw, turn the focus lever to the right/left to determine the focus position while viewing the cameraimages on the monitor, and then re-tighten the screw.4 Tighten the drop-prevention cord fixing screw.NOTE on image direction (Wall Installed):If the monitor image is misaligned, follow the steps below to adjust.c Loosen the screws (B) with the supplied hexagon wrench(small).d Turn the indented dial (C) to adjust the image direction.e Tighten the screws (B) after adjustments are finished.J DAY/NIGHT FUNCTION (VDC-D1584VA)When connected to power, the VDC-D1584VA turns on the DAY/NIGHT function for continuous operation.The DAY/NIGHT function automatically switches over betweencolor and black-and-white mode depending on the ambientbrightness; for example, choosing color mode during daytime, andblack-and-white mode for nighttime monitoring with its increasedsensitivity in a darker environment.NOTE:This function is disabled if 4 is set to "Down".J CAMERA SETTINGSThe camera comes from the factory pre-adjusted and ready toinstall, but you can make adjustments or settings if you need.If you have trouble adjusting the camera, consult your dealer or anAuthorized Sanyo Service Center.(=Factory default setting)1 Backlight compensation setting(VDC-C1574VA, VDC-D1584VA)NOTE:This function is disabled if 4 is set to "Down".If backlight compensation is not corrected in the VDC-C1574VA andVDC-D1584VA when 1 is set to “ON”, you can correct by adjusting levelvolume 6.CONNECTIONS AND SETTINGS60 60ON1 2 3 41 2 3 46677ON1 2 3 42 3 5 4J CONNECTIONSVDC-C1574VA / VDC-D1584VACheck for polarity when using a DC 12 Vpower supply (Polarity does not matter whenusing a AC 24 V power supply).Board on theopposite side of thelensJ LENS ADJUSTMENTS J CAMERA SETTINGSVDC-W1594VABlackRedSupported coaxial cablesYou can use any of the following coaxial cables:RG-59U (3C-2V) Length: 250 m (273.4 yds) max.RG-6U (5C-2V) Length: 500 m (546.8 yds) max.RG-11U (7C-2V) Length: 600 m (656.2 yds) max.When using an RG-59U (3C-2V) cable, do not attach itto piping or wiring.Select the cable according to the distance between thedevices you wish to connect.If you use a cable other than the types above, the imageor sync signal will be attenuated and will not betransmitted correctly.Monitor checkingconnector (a)±180° (Pan)Screw (A)FOCUSZOOM(Tilt)Screw (B)Monitor checkingconnector (a)DC 12 V/AC 24 V connectionScrew(B)Indenteddial (C)Drop-preventioncord fixingscrewON Compensates for backlighting with thecenterweighted metering mode.Down This function is off.2 Iris settingNOTE:This factory preset is optimal, so it is not necessary to change thesetting.3 White balance settingVDC-C1574VA, VDC-D1584VAVDC-W1594VA4 Auto Gain Control (AGC) settingFor adjusting the sensitivity of the camera. Use this setting forshooting in dark environments.5 Wide dynamic range setting (VDC-W1594VA)Correction is made for simultaneous monitoring of subjects whichare different in brightness, one in a dark room and another in brightoutdoor environment, for example.6 Level volumeIf the entire image is too dark or bright, or the backlightcompensation is not correct even after 1 is set to “ON”, you needto adjust the level volume.7 Adjusting synchronization error(AC 24 V users only)Vertical sync disturbance may occur when a selector is used toswitch between multiple cameras connected to one monitor. Toprevent vertical sync disturbance, adjust 7.When using the DC 12V adaptor, sync setting is set to internalsync.ON AI: Normal setting (Auto iris)Down EI: Electronic irisON ATW-A (Auto-tracing white balance - All): Automaticsetting for white balance, covering wider range ofcolor temperature than with “ATW”.• May result in an excessively and unnaturallyeffected image, depending on the conditions.Down ATW (Auto-tracing white balance): Automatic settingfor white balance.ON ATW-A (Auto-tracing white balance - All): Automaticsetting for white balance, covering wider range ofcolor temperature than with “ATW”.• May result in an excessively and unnaturallyeffected image, depending on the conditions.Down ATW (Auto-tracing white balance): Automatic settingfor white balance.ON Normal settingDown Set this when there is excessive noise (AGC off)ON When monitoring of subjects which differ inbrightness.Down This function is off.Counterclockwise(High)Opens the lens iris, making the entireimage brighterClockwise(Low)Closes the lens iris, making the entireimage darkerVDC-C1574VA,VDC-D1584VAPress the button to eliminate syncdisturbances when needed.VDC-W1594VA Press each button to eliminate syncdisturbances when needed.OBLIGATIONSIn order to obtain warranty service, the product must be delivered to and picked up from anAuthorized Sanyo Service Center at the user's expense, unless specifically stated otherwise inthis warranty. The names and addresses of Authorized Sanyo Service Centers may be obtainedby calling the toll-free number listed below.THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED INTHE UNITED STATES OF AMERICA, EXCLUDING ALL U.S. TERRITORIES ANDPROTECTORATES. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAILPURCHASER OR END-USER. THE ORIGINAL DATED BILL OF SALE, SALES SLIP ORRENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICECENTER AT THE TIME WARRANTY SERVICE IS REQUESTED.Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Companywarrants this SANYO product against defects in materials and workmanship for the periodsspecified below. SFC will repair or replace (at its option) the product and any of its parts which failto conform to this warranty. The warranty period commences on the date the product was firstpurchased or rented at retail.SANYO INDUSTRIAL VIDEOCOLOR CCD CAMERA LIMITED WARRANTYFor product operation, authorized service center referral, service assistance or problemresolution, callCUSTOMER INFORMATION 1-800-421-5013Weekdays 8:30 AM – 5:00 PM Pacific TimeFor accessories and/or parts, callPARTS ORDER INFORMATION 1-800-726-9662Weekdays 8:30 AM – 5:00 PM Pacific TimeLABOR PARTS IMAGE DEVICE3 YEARS 3 YEARS 3 YEARSEXCLUSIONSThis warranty does not cover (A) the adjustment of customer-operated controls as explained inthe appropriate model's instruction manual, or (B) the repair of any product whose serial numberhas been altered, defaced or removed.This warranty shall not apply to the cabinet or cosmetic parts, batteries or routine maintenance.This warranty does not apply to uncrating, setup, installation, removal of the product for repair orreinstallation of the product after repair.This warranty does not apply to repairs or replacements necessitated by any cause beyond thecontrol of SFC including, but not limited to, any malfunction, defect or failure caused by or resultingfrom unauthorized service or parts, improper maintenance, operation contrary to furnishedinstructions, shipping or transit accidents, modification or repair by the user, abuse, misuse,neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear andtear.The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorizeany party to assume for it any other obligation or liability.SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TOTHIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS). INNO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIALDAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANYDELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TOCAUSES BEYOND ITS CONTROL. SFC'S LIABILITY FOR ANY AND ALL LOSSES ANDDAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, ARISING OUT OF OR INCONNECTION WITH THE SALE, USE OR OWNERSHIP OF THIS PRODUCT INCLUDINGWARRANTOR'S NEGLIGENCE, ALLEGED DAMAGED OR DEFECTIIVE GOODS, WHETHERSUCH DEFECTS ARE DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THEPURCHASE PRICE OF THE PRODUCT.ATTENTIONFor your protection in the event of theft or loss of this product, please fill in the information belowfor your own personal records.Model No. Serial No.(Located on back or bottom side of unit.)Date of Purchase Purchase PriceWhere Purchased

/ 2

Related manuals for Sanyo VDC-C1574VA - CCTV Camera