Sanyo VPC-E60 Service Manual

Also see for VPC-E60: Instruction manual

Contents

– 19 –3-12. Firmware uploading procedure1. Uploading the firmware should be carried out if the versionnumber (COMPL PWB XX-X) on the replacement circuitboard is lower than the version of the distributed firmware.For XX-X, enter the name of the circuit board containing thefirmware.2. The firmware is distributed by e-mail in self-extracting archiveformat. Change the extension of the distributed file to .EXEand save it in your preferred folder.3. When you double-click the saved file, the firmware (binaryfile) will be saved in the same folder.4. The firmware must not be distributed without permission.1. Overwriting firmware from the SD cardPreparation:SD card: SD card with firmware rewritten into the root direc-toryData: S816Nxxx.BIN (xxx: version)Overwriting method:1. Insert the above SD card.2. Turn on the camera.3. Press the PLAY button.4. Press the MENU button. The playback setting screen ap-pears.5. Choose the OPTION icon.6. Choose the FORMAT.7. Toggle the SET button to the left for 2 seconds. FIRMWAREUPDATE will display.8. Choose YES.9. Press the SET button. Update is starting.Note:Do not turn off the camera’s power or remove the SD cardwhile the firmware is being updated.The power will turn on automatically after the update is com-plete.2. Overwriting firmware from the calibration softwarePreparation:PC with overwriting firmware copied to the preferred folder inthe HD.Data: S816Nxxx.BIN (xxx: version)Overwriting method:1. Connect the camera’s USB/AV terminal to the computer’USB connector.2. The USB Connection screen appears on the camera’s LCDmonitor. Choose the “CARD READER”, and press the SETbutton.3. Double-click on the DscCalDi.exe.4. Click the Firmware.5. Choose the fimware file to use for overwriting, and clickthe Yes.5. Update is starting. The message will appear, and chooseOK.6. After the update is complete, disconnect the USB cableand turn the camera’s power off.Note:Do not turn off the camera’s power while the firmware is be-ing updated.Preparation:Setting of pattern box:Color temperature: 3100 ± 20 (K)Luminance: 900 ± 20 (cd/m2 )Adjusting method:1. Set the camera 0 cm from the pattern box. (Do not enterany light.)2. Double-click on the DscCalDi.exe.3. Select “CCD Black” on the LCD “Test”, and click the “Yes”.4. After the adjustment is completed, the number of defectwill appear.3-8. Factory Code Setting1. Check the "Factory Code" display within the Setting group.2. For U.S.A., Canada and NTSC general areaIf "FC_SANYO_U" does not appear, click on the " " marklocated on the right of the "Factory Code" display BOX andselect "FC_SANYO_U".3. For Europe and PAL general areaIf "FC_SANYO_EX" does not appear, click on the " " marklocated on the right of the "Factory Code" display BOX andselect "FC_SANYO_EX".3-9. Language Setting1. Click on the " " mark located on the right of the"Language" display BOX.2. Select language. (Default is English.)3. End "DscCal" and remove the camera before turning thecamera power OFF.3-10. Reset SettingCarry out reset settings after replacing CP1 board.1. Turn on the camera.2. Press the MENU button.3. Choose the OPTION.4. Choose the RESET SETTINGS, and press the SETbutton.5. Select Yes, and press the SET button.3-11. The Compulsive boot starting method1. Keep MENU button, SET button, and SHUTTER button de-pressed while switching on the power.2. Connect the camera and the computer with USB cable.FirmwareDataAWBFocusUV MatrixRGB OddRGB GainTintRGB EvenVCOMDCPhaseLCDCalibration UploadPAF Cal.LCD Type H AFC TestVCOMPP(LOW)VCOMPP(HI)Cal DataCal ModeOKOKEVFUSB storageGetSetVID SetPID SetSerial SetRev. SetSettingLanguageVideo ModeVCOFactory CodeBackrush pulse : SetGetHall Cal.