Vaillant ecoTEC PLUS SERIES Installation And Maintenance Manual

Also see for ecoTEC plus 612: Instructions for use Instructions for installation and servicing Installation and maintenance instructions Instructions for use Instructions for installation and servicing

Contents

46 Installation and maintenance manual ecoTECDisplay Meaning Display value/adjustable valued.00 Heating partial load Adjustable heating partial load in kW (factory setting: max. output)d.01 Water pump return water time for heating mode 1 - 60 min (factory setting: 5 min)d.02 Max. blocking time heating at 20 °C Flow temperature 2 - 60 min (factory setting: 20 min)d.03 Drinking water flow temperature reading (800 seriesonly)in °Cd.04 Storage temperature reading (only 600 series) in °Cd.05 Flow temperature target value in °C, min. 30 °C and max. the value set in d.71d.06 Drinking water temperature target value in °C, 35 to 65 °Cd.07 Warm start temperature target value (800 series only)Storage temperaturetarget value (600 series only)in °C, 40 to 65 °Cin °C, 15 °C for left stop, then 40 to 65 °Cd.08 Room thermostat at terminal 3-4 0 = Room thermostat open (no heat request)1 = Room thermostat closed (heat request)d.09 Flow target temperature from external analogue regula-tor to terminal 7-8-9/eBusin °C, minimum from ext. eBus target value and target value terminal 7d.10 Status internal heating pump 1, 2 = on, 0 = offd.11 Status external heating pump 1 to 100 = on, 0 = offd.12 Status external storage charging pump 1 to 100 = on, 0 = offd.13 Status external circulation pump 1 to 100 = on, 0 = offd.22 Hot water request, Terminal C1/C2, impeller 1 = on, 0 = offd.25 Storage charging/warm start through warm start clockregulator/release timer1 = yes, 0 = nod.40 Flow temperature Actual value in °Cd.41 Return temperature Actual value in °Cd.47 Outside temperature (with connected VRC 410s) Actual value in °C (uncorrected value)d.67 Remaining burner locking time in mind.76 Appliance variant (device specific number) 00 to 99d.90 Digital regulator status 1 = identified, 0 = unidentified (eBUS Address <=10)d.91 DCF status with connected external probe with DCF77receiver0 = no reception, 1 = reception, 2 = synchronised, 3 = validd.97 Activation of the second diagnosis level Password: 17Table 8.2 Diagnosis codes of the first diagnosis levelDisplay Meaning Display value/adjustable valued.17 Heating flow/return regulation changeover 0 = flow, 1 = return (factory setting: 0)d.18 Pump mode (return flow) 0 = return, 1 = nonstop, 2 = intermittent, 3 = winterd.19 Only in ecoTEC plus:Operating modes of the two-stage heating pump0 = Flow 300 msec Stage 2, then stage 1, drinking water/storagecharging Stage 2, heating stage 2, return stage 11 = Flow 300 msec Stage 2, then stage 1, drinking water/storagecharging Stage 2, heating stage 1, return stage 12 = Flow 300 msec Stage 2, then stage 1, drinking water/storagecharging Stage 2, heating in dependence on d.00, return stage 1(factory setting)3 = Flow Stage 2, drinking water/storage charging Stage 2, heatingstage 2, return stage 2d.26 Changeover option relay to BMU 1 = circulation pump2 = ext. pump3 = Storage charging pump4 = solar pumpd.27 Changeover accessory relay 1 -d.28 Changeover accessory relay 2 -d.30 Control signal for both gas valves 1 = on, 0 = offd.33 Fan speed target value in rpm/10d.34 Fan speed actual value in rpm/10d.35 Position of priority reverse valve (only 800 series) 0 = Heating; 1 = Hot water; 2 = Centre positiond.44 Ionisation current Actual value/100 in μAd.50 Offset for minimum speed in rpm/10, adjustment range: 0 to 254 (Factory setting: 20)d.51 Offset for maximum speed in rpm/10, adjustment range: -99 to -0 (Factory setting: -30)d.60 Number of temperature limiting cut-offs QuantityTable 8.3 Diagnosis codes of the second diagnosis level8 Troubleshooting