Watts PWSR Series Installation, Operation And Maintenance Manual

Contents

Watts PWSR Series Installation, Operation And Maintenance Manual Manual pdf 13 page image

PWSR Series Softeners 13Control ProgrammingGeneral OperationUser (U) Displays/SettingsWhen the system is operating one of two displays will beshown. Pressing NEXT will alternate between the displays.One of the displays is always the current time of day. Thesecond display is one of the following: days remaining orgallons remaining. Days remaining are the number of daysleft before the system goes through a regeneration cycle.Capacity remaining is the number of gallons that will be treat-ed before the system goes through a regeneration cycle. Theuser can scroll between the displays as desired.If the system has called for a regeneration that will occur atthe preset time of regeneration, the words REGEN TODAYwill appear on the display.When water is being treated (i.e. water is flowing through thesystem) the word “Softening” flashes on the display.REGENERATION MODETypically a system is set to regener-ate at a time of low water usage. Anexample of a time with low waterusage is when a household is asleep.If there is a demand for water when the system is regenerating,untreated water will be used.When the system begins to regenerate, the display will changeto include information about the step of the regeneration processand the time remaining for that step to be completed. The systemruns through the steps automatically and will reset itself to pro-vide treated water when the regeneration has been completed.MANUALREGENERATIONSometimes there is aneed to regeneratethe system, soonerthan when the system calls for it, usually referred to as manualregeneration. There may be a period of heavy water usagebecause of guests or a heavy laundry day.To initiate a manual regeneration at the preset delayed regener-ation time, when the regeneration time option is set to “NORMAL”or “NORMAL + on 0”, press and release “REGEN”. The words“REGEN TODAY” will flash on the display to indicate that the sys-tem will regenerate at the preset delayed regeneration time. Ifyou pressed the “REGEN” button in error, pressing the buttonagain will cancel the request. Note: If the regeneration timeoption is set to “on 0” there is no set delayed regeneration timeso “REGEN TODAY” will not activate if “REGEN” button ispressed.To initiate a manual regeneration immediately, press and hold the“REGEN” button for three seconds. The system will begin toregenerate immediately. The request cannot be cancelled.11CONTROL PROGRAMMINGINSTALLER (I) Displays/SettingsSTEP 1I – Press NEXT and arrow up simulta-neously for 3 seconds.STEP 2I – Hardness: Set the amount of hard-ness in grains of hardness as calcium carbonateper gallon using, arrow down or arrow up but-tons. The default is 20 with value ranges from 1to 150 in 1 grain increments. Note the grains pergallon can be increased if soluble iron needs tobe reduced. Press NEXT to go to step 3I. PressREGEN to exit Installer Displays/Settings.STEP 3I – Day Override: When gallon capacityis set to off, sets the number of days betweenregeneration’s. When gallon capacity is set toAUTO or to a number sets the maximum numberof days between regeneration. If value set to “off”regeneration initiation is based solely on gallonsused. If value is set as a number (allowablerange from 1 to 28) a regeneration initiationwill be called for on that day even if sufficientnumber of gallons were not used to call fora regeneration. Set Day Override using arrowbuttons: number to days between regeneration(1 to 28); or OFF.Press NEXT to go to step 4I. Press REGEN toreturn to previous step.STEP 4I – Next Regeneration Time (hour): Setthe hour of day for regeneration using down or uparrow buttons. AM/PM toggles after 12. Thedefault time is 2:00 am. This display shows“REGEN on 0 GAL” if “on 0” is selected in Step9S or Step 7F. Press NEXT to go to step 5I.Press REGEN to return to previous step.STEP 5I – Next Regeneration Time (minutes):Set the minutes of day regeneration using downor up arrow buttons. This display not be shown if“on 0” is selected in Step 9S or Step 7F. PressNEXT to exit Installer Displays/ Settings. PressREGEN to return to previous step.To initiate a manual regeneration immediately,press and hold the “REGEN” button for threeseconds. The system will beam to regenerateimmediately. The control valve may be steppedthrough the various regeneration cycles bypressing the “REGEN” button.Note: If brine tank does not contain salt, fill with saltand wait at least two hours before regenerating.Installer (I) Displays/SettingsSTEP 1I – Press NEXT and arrow up simultaneouslyfor 3 secondsSTEP 2I – Hardness: Set the amount of hardnessin grains of hardness as calcium carbonate pergallon using, arrow down or arrow up but-tons Thedefault is 20 with value ranges from 1 to 150 in 1grain increments Note the grains per gallon can beincreased if soluble iron needs to be reduced PressNEXT to go to step 3I Press REGEN to exit InstallerDisplays/SettingsSTEP 3I – Day Override: When gallon capacityis set to off, sets the number of days betweenregeneration’s When gallon capacity is set to AUTOor to a number sets the maximum number of daysbetween regeneration If value set to “off” regenerationinitiation is based solely on gallons used If value isset as a number (allowable range from 1 to 28) aregeneration initiation will be called for on that dayeven if sufficient number of gallons were not used tocall for a regeneration Set Day Override using arrowbuttons: number to days between regeneration (1 to28); or OFFPress NEXT to go to step 4I Press REGEN to returnto previous stepSTEP 4I – Next Regeneration Time (hour): Set thehour of day for regeneration using down or up arrowbuttons AM/PM toggles after 12 The default time is2:00 am This display shows “REGEN on 0 GAL” if “on0” is selected in Step 9S or Step 7F Press NEXT to goto step 5I Press REGEN to return to previous stepSTEP 5I – Next Regeneration Time (minutes): Set theminutes of day regeneration using down or up arrowbuttons This display not be shown if “on 0” is selectedin Step 9S or Step 7F Press NEXT to exit InstallerDisplays/ Settings Press REGEN to return to previousstepTo initiate a manual regeneration immediately, pressand hold the “REGEN” button for three secondsThe system will beam to regenerate immediately Thecontrol valve may be stepped through the variousregeneration cycles by pressing the “REGEN” buttonGeneral OperationUser (U) Displays/SettingsWhen the system is operating one of two displays will beshown. Pressing NEXT will alternate between the displays.One of the displays is always the current time of day. Thesecond display is one of the following: days remaining orgallons remaining. Days remaining are the number of daysleft before the system goes through a regeneration cycle.Capacity remaining is the number of gallons that will be treat-ed before the system goes through a regeneration cycle. Theuser can scroll between the displays as desired.If the system has called for a regeneration that will occur atthe preset time of regeneration, the words REGEN TODAYwill appear on the display.When water is being treated (i.e. water is flowing through thesystem) the word “Softening” flashes on the display.REGENERATION MODETypically a system is set to regener-ate at a time of low water usage. Anexample of a time with low waterusage is when a household is asleep.If there is a demand for water when the system is regenerating,untreated water will be used.When the system begins to regenerate, the display will changeto include information about the step of the regeneration processand the time remaining for that step to be completed. The systemruns through the steps automatically and will reset itself to pro-vide treated water when the regeneration has been completed.MANUALREGENERATIONSometimes there is aneed to regeneratethe system, soonerthan when the system calls for it, usually referred to as manualregeneration. There may be a period of heavy water usagebecause of guests or a heavy laundry day.To initiate a manual regeneration at the preset delayed regener-ation time, when the regeneration time option is set to “NORMAL”or “NORMAL + on 0”, press and release “REGEN”. The words“REGEN TODAY” will flash on the display to indicate that the sys-tem will regenerate at the preset delayed regeneration time. Ifyou pressed the “REGEN” button in error, pressing the buttonagain will cancel the request. Note: If the regeneration timeoption is set to “on 0” there is no set delayed regeneration timeso “REGEN TODAY” will not activate if “REGEN” button ispressed.To initiate a manual regeneration immediately, press and hold the“REGEN” button for three seconds. The system will begin toregenerate immediately. The request cannot be cancelled.11CONTROL PROGRAMMINGINSTALLER (I) Displays/SettingsSTEP 1I – Press NEXT and arrow up simulta-neously for 3 seconds.STEP 2I – Hardness: Set the amount of hard-ness in grains of hardness as calcium carbonateper gallon using, arrow down or arrow up but-tons. The default is 20 with value ranges from 1to 150 in 1 grain increments. Note the grains pergallon can be increased if soluble iron needs tobe reduced. Press NEXT to go to step 3I. PressREGEN to exit Installer Displays/Settings.STEP 3I – Day Override: When gallon capacityis set to off, sets the number of days betweenregeneration’s. When gallon capacity is set toAUTO or to a number sets the maximum numberof days between regeneration. If value set to “off”regeneration initiation is based solely on gallonsused. If value is set as a number (allowablerange from 1 to 28) a regeneration initiationwill be called for on that day even if sufficientnumber of gallons were not used to call fora regeneration. Set Day Override using arrowbuttons: number to days between regeneration(1 to 28); or OFF.Press NEXT to go to step 4I. Press REGEN toreturn to previous step.STEP 4I – Next Regeneration Time (hour): Setthe hour of day for regeneration using down or uparrow buttons. AM/PM toggles after 12. Thedefault time is 2:00 am. This display shows“REGEN on 0 GAL” if “on 0” is selected in Step9S or Step 7F. Press NEXT to go to step 5I.Press REGEN to return to previous step.STEP 5I – Next Regeneration Time (minutes):Set the minutes of day regeneration using downor up arrow buttons. This display not be shown if“on 0” is selected in Step 9S or Step 7F. PressNEXT to exit Installer Displays/ Settings. PressREGEN to return to previous step.To initiate a manual regeneration immediately,press and hold the “REGEN” button for threeseconds. The system will beam to regenerateimmediately. The control valve may be steppedthrough the various regeneration cycles bypressing the “REGEN” button.Note: If brine tank does not contain salt, fill with saltand wait at least two hours before regenerating.General OperationUser (U) Displays/SettingsWhen the system is operating one of two displays will be shownPressing NEXT will alternate between the displays One of thedisplays is always the current time of day The second display is oneof the following: days remaining or gallons remaining Days remainingare the number of days left before the system goes through aregeneration cycle Capacity remaining is the number of gallons thatwill be treated before the system goes through a regeneration cycleThe user can scroll between the displays as desiredIf the system has called for a regeneration that will occur at thepreset time of regeneration, the words REGEN TODAY will appear onthe displayWhen water is being treated (i e water is flowing through the system)the word “Softening” flashes on the displayNOTICEIf brine tank does not contain salt, fill with salt and wait at leasttwo hours before regeneratingRegeneration ModeTypically a system is set to regenerate ata time of low water usage An exampleof a time with low water usage is when ahousehold is asleepIf there is a demand for water when the system is regenerating,untreated water will be usedWhen the system begins to regenerate, the display will changeto include information about the step of the regeneration processand the time remaining for that step to be completed The systemruns through the steps automatically and will reset itself to pro-videtreated water when the regeneration has been completedManualRegenerationSometimes there is aneed to regenerate thesystem, sooner than whenthe system calls for it, usually referred to as manual regenerationThere may be a period of heavy water usage because of guests or aheavy laundry dayTo initiate a manual regeneration at the preset delayed regenerationtime, when the regeneration time option is set to “NORMAL” or“NORMAL + on 0”, press and release “REGEN” The words “REGENTODAY” will flash on the display to indicate that the system willregenerate at the preset delayed regeneration time If you pressedthe “REGEN” button in error, pressing the button again will cancelthe request Note: If the regeneration time option is set to “on 0”there is no set delayed regeneration time so “REGEN TODAY” willnot activate if “REGEN” button is pressedTo initiate a manual regeneration immediately, press and holdthe “REGEN” button for three seconds The system will begin toregenerate immediately The request cannot be cancelledGeneral OperationUser (U) Displays/SettingsWhen the system is operating one of two displays will beshown. Pressing NEXT will alternate between the displays.One of the displays is always the current time of day. Thesecond display is one of the following: days remaining orgallons remaining. Days remaining are the number of daysleft before the system goes through a regeneration cycle.Capacity remaining is the number of gallons that will be treat-ed before the system goes through a regeneration cycle. Theuser can scroll between the displays as desired.If the system has called for a regeneration that will occur atthe preset time of regeneration, the words REGEN TODAYwill appear on the display.When water is being treated (i.e. water is flowing through thesystem) the word “Softening” flashes on the display.REGENERATION MODETypically a system is set to regener-ate at a time of low water usage. Anexample of a time with low waterusage is when a household is asleep.If there is a demand for water when the system is regenerating,untreated water will be used.When the system begins to regenerate, the display will changeto include information about the step of the regeneration processand the time remaining for that step to be completed. The systemruns through the steps automatically and will reset itself to pro-vide treated water when the regeneration has been completed.MANUALREGENERATIONSometimes there is aneed to regeneratethe system, soonerthan when the system calls for it, usually referred to as manualregeneration. There may be a period of heavy water usagebecause of guests or a heavy laundry day.To initiate a manual regeneration at the preset delayed regener-ation time, when the regeneration time option is set to “NORMAL”or “NORMAL + on 0”, press and release “REGEN”. The words“REGEN TODAY” will flash on the display to indicate that the sys-tem will regenerate at the preset delayed regeneration time. Ifyou pressed the “REGEN” button in error, pressing the buttonagain will cancel the request. Note: If the regeneration timeoption is set to “on 0” there is no set delayed regeneration timeso “REGEN TODAY” will not activate if “REGEN” button ispressed.To initiate a manual regeneration immediately, press and hold the“REGEN” button for three seconds. The system will begin toregenerate immediately. The request cannot be cancelled.11CONTROL PROGRAMMINGINSTALLER (I) Displays/SettingsSTEP 1I – Press NEXT and arrow up simulta-neously for 3 seconds.STEP 2I – Hardness: Set the amount of hard-ness in grains of hardness as calcium carbonateper gallon using, arrow down or arrow up but-tons. The default is 20 with value ranges from 1to 150 in 1 grain increments. Note the grains pergallon can be increased if soluble iron needs tobe reduced. Press NEXT to go to step 3I. PressREGEN to exit Installer Displays/Settings.STEP 3I – Day Override: When gallon capacityis set to off, sets the number of days betweenregeneration’s. When gallon capacity is set toAUTO or to a number sets the maximum numberof days between regeneration. If value set to “off”regeneration initiation is based solely on gallonsused. If value is set as a number (allowablerange from 1 to 28) a regeneration initiationwill be called for on that day even if sufficientnumber of gallons were not used to call fora regeneration. Set Day Override using arrowbuttons: number to days between regeneration(1 to 28); or OFF.Press NEXT to go to step 4I. Press REGEN toreturn to previous step.STEP 4I – Next Regeneration Time (hour): Setthe hour of day for regeneration using down or uparrow buttons. AM/PM toggles after 12. Thedefault time is 2:00 am. This display shows“REGEN on 0 GAL” if “on 0” is selected in Step9S or Step 7F. Press NEXT to go to step 5I.Press REGEN to return to previous step.STEP 5I – Next Regeneration Time (minutes):Set the minutes of day regeneration using downor up arrow buttons. This display not be shown if“on 0” is selected in Step 9S or Step 7F. PressNEXT to exit Installer Displays/ Settings. PressREGEN to return to previous step.To initiate a manual regeneration immediately,press and hold the “REGEN” button for threeseconds. The system will beam to regenerateimmediately. The control valve may be steppedthrough the various regeneration cycles bypressing the “REGEN” button.Note: If brine tank does not contain salt, fill with saltand wait at least two hours before regenerating.General OperationUser (U) Displays/SettingsWhen the system is operating one of two displays will beshown. Pressing NEXT will alternate between the displays.One of the displays is always the current time of day. Thesecond display is one of the following: days remaining orgallons remaining. Days remaining are the number of daysleft before the system goes through a regeneration cycle.Capacity remaining is the number of gallons that will be treat-ed before the system goes through a regeneration cycle. Theuser can scroll between the displays as desired.If the system has called for a regeneration that will occur atthe preset time of regeneration, the words REGEN TODAYwill appear on the display.When water is being treated (i.e. water is flowing through thesystem) the word “Softening” flashes on the display.REGENERATION MODETypically a system is set to regener-ate at a time of low water usage. Anexample of a time with low waterusage is when a household is asleep.If there is a demand for water when the system is regenerating,untreated water will be used.When the system begins to regenerate, the display will changeto include information about the step of the regeneration processand the time remaining for that step to be completed. The systemruns through the steps automatically and will reset itself to pro-vide treated water when the regeneration has been completed.MANUALREGENERATIONSometimes there is aneed to regeneratethe system, soonerthan when the system calls for it, usually referred to as manualregeneration. There may be a period of heavy water usagebecause of guests or a heavy laundry day.To initiate a manual regeneration at the preset delayed regener-ation time, when the regeneration time option is set to “NORMAL”or “NORMAL + on 0”, press and release “REGEN”. The words“REGEN TODAY” will flash on the display to indicate that the sys-tem will regenerate at the preset delayed regeneration time. Ifyou pressed the “REGEN” button in error, pressing the buttonagain will cancel the request. Note: If the regeneration timeoption is set to “on 0” there is no set delayed regeneration timeso “REGEN TODAY” will not activate if “REGEN” button ispressed.To initiate a manual regeneration immediately, press and hold the“REGEN” button for three seconds. The system will begin toregenerate immediately. The request cannot be cancelled.11CONTROL PROGRAMMINGINSTALLER (I) Displays/SettingsSTEP 1I – Press NEXT and arrow up simulta-neously for 3 seconds.STEP 2I – Hardness: Set the amount of hard-ness in grains of hardness as calcium carbonateper gallon using, arrow down or arrow up but-tons. The default is 20 with value ranges from 1to 150 in 1 grain increments. Note the grains pergallon can be increased if soluble iron needs tobe reduced. Press NEXT to go to step 3I. PressREGEN to exit Installer Displays/Settings.STEP 3I – Day Override: When gallon capacityis set to off, sets the number of days betweenregeneration’s. When gallon capacity is set toAUTO or to a number sets the maximum numberof days between regeneration. If value set to “off”regeneration initiation is based solely on gallonsused. If value is set as a number (allowablerange from 1 to 28) a regeneration initiationwill be called for on that day even if sufficientnumber of gallons were not used to call fora regeneration. Set Day Override using arrowbuttons: number to days between regeneration(1 to 28); or OFF.Press NEXT to go to step 4I. Press REGEN toreturn to previous step.STEP 4I – Next Regeneration Time (hour): Setthe hour of day for regeneration using down or uparrow buttons. AM/PM toggles after 12. Thedefault time is 2:00 am. This display shows“REGEN on 0 GAL” if “on 0” is selected in Step9S or Step 7F. Press NEXT to go to step 5I.Press REGEN to return to previous step.STEP 5I – Next Regeneration Time (minutes):Set the minutes of day regeneration using downor up arrow buttons. This display not be shown if“on 0” is selected in Step 9S or Step 7F. PressNEXT to exit Installer Displays/ Settings. PressREGEN to return to previous step.To initiate a manual regeneration immediately,press and hold the “REGEN” button for threeseconds. The system will beam to regenerateimmediately. The control valve may be steppedthrough the various regeneration cycles bypressing the “REGEN” button.Note: If brine tank does not contain salt, fill with saltand wait at least two hours before regenerating.