Wayne-Dalton 8100 Installation Instructions And Owner's Manual

Also see for 8000 Series: Installation instructions and owner's manual Installation instructions and owner's manual Installation instructions and owner's manua Quick start guide Installation instructions and owner's manual

Contents

Wayne-Dalton 8100 Installation Instructions And Owner's Manual Manual pdf 3 page image

weatherstrip in the header and flush with the inside edge of the jamb. Temporarily securethe weatherstrip with equally spaced nails. Repeat for other side. This will keep the bottomsection from falling out of the opening during installation. Equally space nails approximately12” to 18” apart.FOR FULLY ADJUSTABLE TRACK: For the header, align the weatherstrip 1/8” to 1/4” insidethe header edge, and temporarily secure it to the header with equally spaced nails. Startingat either side of the jamb, fit the weatherstrip up tight against the temporarily attachedweatherstrip in the header and 1/8” to 1/4” inside the jamb edge. Temporarily secure theweatherstrip with equally spaced nails. Repeat for other side. This will keep the bottom sec-tion from falling out of the opening during installation. Equally space nails approximately 12”to 18” apart.HEADROOM REQUIREMENT: Headroom is defined as the space needed above the top ofthe door for tracks, springs, etc. to allow the door to open properly. If the door is to be motoroperated, 2-1/2” (64 mm) of additional headroom is required.NOTE: 6” low headroom conversion kit is available for 12” radius only. Contact your localWayne Dalton dealer.BACKROOM REQUIREMENT: Backroom is defined as the distance needed from the openingback into the garage to allow the door to open fully.*NOTE: For door heights from 10’1” to 14’0”, refer to your operator manufacture installationinstructions for appropriate depth into room.BACKROOM REQUIREMENTSDoor Height Track Manual Lift Motor Operated6’0” to 7’0” 12”, 15” Radius 102” (2591 mm) 125” (3175 mm)7’1” to 8’0” 12”, 15” Radius 114” (2896 mm) 137” (3480 mm)8’1” to 9’0” 12”, 15” Radius 126” (3200 mm) 168” (4267 mm)9’1” to 10’0” 12”, 15” Radius 138” (3505 mm) 168” (4267 mm)10’1” to 12’0” 12”, 15” Radius 162” (4115 mm) See *NOTE12’1” to 14’0” 12”, 15” Radius 186” (4724 mm) See *NOTEHEADROOM REQUIREMENTSTrack Type Space Needed12” Radius 13-1/2” (343 mm)15” Radius 14-1/2” (368 mm)WeatherstripsLevel headerFinishedDoor widthJambsBackroomPlumbjambsFinishedDoorHeightNailHeadroomHeader board 2”x 6”lumber preferredSuitable mounting surface2”x 6” lumber minimumWeatherstripsJambQuick Install trackOther track systemsJamb1/8” to 1/4”Min. SideroomClearanceis 3-1/2”Min. SideroomClearanceis 3-1/2”Package ContentsNOTE: Depending on the door model, some parts listed will not be supplied if not required.Rear Back Hangs may not be included with your door.Door sections (as required)Torsion shaft / Torsion keyed shaft (as required)Torsion keyed shafts (as required)Vertical tracks RH/LH (as required)Q.I. flag angles RH/LH (as required) F.A. flag angles RH/LH (as required)Riveted vertical track assemblies RH/LH (as required)Horizontal tracks RH/LH (as required)Angle mount vertical track assemblies RH/LH (as required)(2) Horizontal track angles (as required)Quick install jambbrackets (as required) Fully Adjustable jambbrackets (as required) Weatherstrips &nails (If included)JB-US Jambbrackets(as required)Strut (U-shaped)(if included) Bottom corner bracketsRH/LH (as required)(2) Lift handles &Spacers (1) Step plate(as required)(2) Step plates(as required) (1) Step plates(as required) Pushnuts(as required)Top fixture assemblies(as required) Top fixture assemblies(as required)Graduatedhinges (as required)Extension brackets(as required)Track rollers(as required)(2) RollerspacersPull downrope (if included)Bottom cornerbrackets (as required) Bottom cornerbrackets (as required) Track roller carriers(as required) Cable drums RH/LH3