Zenith SENTRY 2 SY2765 Operating Manual & Warranty

Contents

GET TO KNOW THE REMOTE CONTROL;" MBR3447PROGRAMMING YOUR REMOTEIf you are using Zenith products, the remote is programmed for the most commonly used codes. For other audio/video brands youwill have to program the remote.Follow these steps for each product you are usingTo program the remote1. Locate t:he three-digit code for your brand (such as Zenith) andequipment (such as VCR) in the code table.2. Press and hold PRG with a small blunt object until the indicatorlights (about three seconds).3. Press TV, VCR, CABLE or AUX to select the product youwant your remote to control. (Use CABLE or AUX to pro-gram your remote for a second TV or VCR or to programyour remote for a video disc player, audio equipment or acable box.)4. Enter the three-digit code, then press ENTER. The indicator lightshould flash, then turn offto indicate that the code was accepted. Ifthe light stays on, repeat steps 3 and 4 or try using a different code.5. Write the codes that operate your equipment on the labelinside the battery compartment for future reference.Notes:To erase all code programming and return to the factorypreset codes, enter code 9--1--1 when programming theremote.[] If no key on your remote is pressed within 60 seconds, theprogramming process will stop, and you will have to startagain.[] You may cancel programming at any time by pressing PRG.;SPECIAL FEATURESAUX+I, AUX+2, AUX+3 CAPABILITYYour remote can control up to seven electronic components. Ifyou have programmed the remote for four components using theTV, VCR, CABLE and AUX keys, you may also program it fortip to three additional components.To program AUX+I, AUX+2, & AUX+31. Locate the three-digit code for your equipment in the code table.2. Press and hold PRG until the indicator lights.3. Press AUX and "1" simultaneously to select AUX+I.4. Enter the three-digit code then press ENTER. The indicator lightshould flash then turn off to indicate that the code was accepted. Ifthe light stays on, repeat steps 3 and 4 or try using a different code.5. Repeat steps 2-- 4 for AUX+2 and AUX+3 programming.6. Write the codes that operate your equipment on the labelinside the battery compartment for future reference.Once progrgrnmed, hold down the AUX key and press 1, 2 or 3,to access the additional AUX +1, 2 or 3 mode.CABLE BOX VOLUME"You may use your remote to control cable box volume andmuting if available on your equipment.' TO program the cable box volume I[Program yo__ c-ode__e AUX mode."ll121 Repeat the programming steps, again using the CABLE or AUX tlkEY,bNTEUl_.key-incode 3-9-9 instead °f a brand code and press 1Note:(21 To restore TV volume/mute control to the CABLE or AUXmode, reprogram your cable code in that mode.AMPLIFIER VOLUME OVERRIDEYou may use your remote to ow,'rride your TV, VCR, cablebox or video disk player's volume functions with your ampli-tier','; volume and muting.To program the amplifier volume overrideI. Program your amplifier cod,," into the CABLE or one of theAUX modes.2. Select the mode on your remote (TV, VCR, etc.) where youwant the amplifier volume control function to appear. For exam-ple, if you want to operate the volume and mute of ),our ampli-fier while the remote is in TV mode, press TV for this step.3. Enter code 4--9--9, followed by ENTER.The amplifier volume and mute fimtures are now available in theselected mode.Notes:O To restore normal volume and muting control to yourequipment, reprogram the remote for these units into eachmode (TV, VCR, etc.) to be restored.[El CD and tape devices will automatically select amplifiervolume and mute. (If an amplifier is programmed into theremote.)....... ,t _A