Zenith SYSTEM 3 SY2738RK Operating Manual & Warranty

Contents

Zenith SYSTEM 3 SY2738RK Operating Manual & Warranty Manual pdf 15 page image

GEM4000 VCR PLUS+C3( ) REMOTE CONTROLSET THE CLOCK IN THE REMOTEUse the numbers on the remote and other keys as listed below._ii_i_iii_i _ __i_ _!!:.__/ii::@ii!i::__::_::_i_ii__i:.i:.i__::__::i_ _ii::_o_i!i!_!_ii_i_i__i::!::____ i_ ::::::::::::::::::::::::::::::::::::::::::::::::::::::___t_::_::i::__i_::i__::ii:__iii_i!:.i::i:.i!!::_:.!_:@_!_!_ __!_!_ _i_i_!___i:_i::i_i!:!_:!/_!__ i:.i:.i:::i_it _i!_!__ii____!_ _i__i____i_.!_ii_i_.1. Press PRG (Program)2. Press CLOCK (MENU)3. Enter the hour (1-12), press ENTER4. Enter the minutes (0-59), press ENTER5. Enter 1 for AM or 2 for PM6. Enter the month (1-12), press ENTER7. Enter the date (1-31), press ENTER8. Enter the year (00-99), press ENTERPROGRAMHr-__Hr- xxMin - x x1 AM 2 PMMO- xxDA- xxYR- xxnr-Min - __1 AM 2 PMMO-DA-YR-OKSPECIAL FEATURES CODESIf you have problems recording when using the VCR Plus+C 3 recording system with your VCR and/or cable box, see if these canbe resolved by programming in one of the special features codes. These codes may enable the remote to control your brand ofequipment.Notes:• To erase these special features, simply reprogram each brand code you are using into the CABLE, VCR, and AUX modes.• These special features codes are only transmitted during VCR Plus+C 3 recording, not regular TV operations.• For future reference, write the codes you are using here:Cable CodeVCR CodeAux CodeCode 599, Add ENTERSome cable boxes and VCRs require an ENTER code to selecta channel. When you program 599 into either the CABLE orVCR mode, the remote transmits the ENTER code for eitherthe cable box or the VCR during a VCR Plus+C 3 recording.This feature cannot be active at the same time as the 699CH 100 feature described below.Code 699, Send CH100Some cable boxes and VCRs require a CH100 code to tune a3-digit channel. When you program 699 into either theCABLE or VCR mode, the remote transmits a CH100 code, ifrequired, during a VCR Plus+C 3 recording.This feature cannot be active at the same time as the 599 AddENTER feature, described above.Code 799, Increase Digit SeparationThis feature, when programmed into either the CABLE orVCR mode, increases the time between digit transmissions to1 second during VCR Plus+ recording. Use this feature if thedefault time between digit transmissions is too short for theVCR or cable box.Code 899, Digit OverrideIf a VCR brand code has been programmed into the VCRmode but the CABLE mode has no brand code programmedinto it, the remote will transmit VCR digits during a VCRPlus+C 3 recording. If a cable brand code has beenprogrammed into the CABLE mode, the remote will transmitcable digits (it selects channels on the cable box) during aVCR Plus+C 3 recording. Programming 899 into the CABLEor VCR mode forces the remote to transmit VCR channelnumbers during a VCR Plus+C 3 recording even if a cable boxcode has been programmed into the CABLE mode.Code 999, Decrease Digit SeparationThis feature, when programmed into either the CABLE orVCR modes, decreases the time between digit transmissions to0.2 seconds during a VCR Plus+C 3 recording. Use this featureif the default time between digits transmission is too long forthe VCR or cable box.3130A-O 4 -- 3