Zip HydroTap G4 Celsius Installation Instructions Manual

Also see for Celsius HydroTap G4 range: Installation instructions User manual Installation instructions Installation instructions User guide

Contents

Page 8 of 28 802149UK Celsius residential - Installation instructions -Jan 2016 v2.03Major components and accessoriesAccessories DescriptionScale filterinstallation kit*ZT200G4Filter not included.Replacementinternal 0.2 micronfilterZT4021 XCO2 gas cylinderZT400Recommendedwater blockHE45004Parts supplied DescriptionTap options1 xCelsius ArcBoiling or chilled orchilled sparkling tap1 xCelsius CubeBoiling or chilled orchilled sparkling tapCommand-CentreTM and componentsVent kit(C ,CS models only)1 x Outlet vent (C)2 x Outlet vent (CS)1 x Inlet vent1 xCommand-CentreTMwith air and waterfilters1 x Mains waterconnection hose1 x T-piece &adaptor1 x User guide and1 x Quick startguide1 x Installationinstruction1 xCO2 gas cylinderassembly(CS models only)801599 - HydroTap User Guide - Nov 2013 UK - V1.05 Page 1 of 20ZIP HydroTapUser Guide®• Tap Operation...................(Pages 2-5)• LCD Screen & Menu .......(Pages 6-18)• Maintenance.................... (Pages 18-20)• Date of Installation.........Affix Model Number LabelHere801599BC160/125G4BC240/175G4BCH160/125G4BCH240/175G4AV160/125G4AN160/125G4AV240/175G4AN240/175G4801600 - Zip Quick Start Guide - October 2013 - V1.06Parts Supplied Description Parts Supplied Description1 offHydrotap Tapand hosesDuct kit1x Air Duct1 x Mountingplate1 offUndersink Unitwith air and water-filterVent kit1 x Kickboardlouvre1 x Door ventlouvre1 x front vent grill1 x Restrictaflowvalve and Teepiece for MixerTaps1 offHydroTapBooster heaterand hoses(Supplied with240/175 models)1 off Mains waterconnection hoseQUICK START GUIDENote: This quick start guide must be read in conjunction withthe main installation and user instructions• Before proceeding, read the installation and user instructions• Check all the components are present and correct.• Check that you have all the necessary tools• Ensure the underbench can support the product weight when full of water,(Check the specifications in the main book and allow an extra 5-8kg when full. )Before installing ensure the following have been provided atthe installation site:• Sufficient space in the cupboard to install all of the undersink units in accordancewith these Installation Instructions. Refer to technical specification for dimensions. Ifrequired, make allowance for a booster heater. (Refer to the main book, for detailedinstallation instructions).• A potable water supply connection with isolating valve inside the cupboard withinreach of the flexible braided hose and positioned so that the connection point and thestop cock will not be obstructed when all the undersink units are installed.• For Zip HydroTap 160/125 &160/175 models, a 220-240Vac, 10A GPO will berequired. For Zip HydroTap 240/175 models, two 220-240Vac, 10A GPOs will berequired. (One GPO is for the Zip HydroTap and the other for the Booster heater).NOTE: Check the cable lengths and outlet positions before proceeding.• A potable cold water supply with a minimum working pressure of 172kPa and amaximum working pressure of 700kPa connected via an isolation valve.• For the mains pressure All-IN-ONE, both a hot and cold water supply will be required.• The undersink appliances must be mounted in upright positions as shown in thediagrams.IMPORTANT! Do not proceed with the installation if theserequirements are not met.STEP 1- Prepare and fit the TapsHole positioning: Position the tap such that it dispenses intothe sink bowl with ample clearance for a cup or tea pot. Alternatively,the tap could be mounted away from the sink using a Zip Font, avail-able as an accessory.Apply a light smearing of silicon sealanton the underside of the upper spacer toensure a watertight fit.For HydroTap and Mixer tapscut a 35mm hole in the bench / sink top.BENCH TOPØ35mmHydroTap TapMixer Tap 4-in-1 (If required)NUTLOWER RUBBERWASHERUPPERRUBBERWASHERWASHERBRAIDEDHOSE x 3UPPER RUB-BER WASHERLOWER RUB-BER WASHERWASHERNUTWhite HoseExt. MainsBlue bandMixer INRed bandMixer OutO-RINGBASEBLOCKSPIDERBASEBLOCKNUT USBCABLEALLTHREADRODNOTE: feed each ofthe tubes and elec-trical cable evenly inbetween the legs ofthe BASE BLOCKSPIDER.All-In-One Tap (If required)For AIO mains and vented TapsCut a 50mm hole in the bench / sink top.NOTE: make sure the tap location will allow the nozzle to drain into the sink.SINK TOP50mmALL THREADRODSTAINLESSSTEELWASHERSPIDERCLAMPNUTBLACKPLASTICSPACERNOTE: feed each of the three tubes andelectrical cable evenly in between the legs ofthe SPIDER CLAMP when installing.Fit theSTAINLESS STEELWASHER,SPIDER CLAMP,AND 6mm NUT.6mmNUTSPIDERCLAMPStainlesswasherBlack plasticspacer35mm dia holeSinkO-RING SINK TOPFit the O-ring to the underside of the AIO tapthen pass all hoses through the 50mm hole.ChillerconnectionBLUEFrom Mixer OUT to Tap - Vented version onlyBoilerconnectionREDBlue ring onRHS mains IN toMixer INWhite ringon LHS toMains inTapO ring BaseClear tube to Vent*ZT200G4 kit to fit filters FL1100