eBridge eBridge8E Installation Manual
        | |
www.altronix.com - 3 - eBridge8E / eBridge800EElevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient.Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromisedMechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.Circuit Overloading - Consideration should be given to the connection of the equipment to supply circuit and the effect that overloading of the circuits might have on overcurrentprotection and supply wiring. Appropriate consideration of equipment nameplate rating should be used when addressing this concern.1. Attach mounting brackets to eBridge unit for rack or wall mount installation (Figs. 4 & 5, pg. 8). Affix rubber pads to the unit for shelf installation (Fig. 6, pg. 8).2. Unit should be located in proximity to ethernet switch/network, NVR or video server.3. Plug the grounded AC line cord (included) into the IEC 320 connector of the eBridge unit (Fig. 1, pg. 4). Plug unit into a reliable earth grounded socket.When using multiple units the sum of the individual name plate ratings should not exceed the supply circuit rating.Do not connect to a receptacle controlled by a switch.4. Connect structured cable(s) from ethernet switch/NVR (network video server) to RJ45 jack marked [1Gb] (Fig. 2, pg. 4).5. Connect Coax cable to BNC connector marked [Data In] (Fig. 1, pg. 4).6. eBridge1PCTX/eBridge1ST connected to eBridge8E, eBridge100TM/eBridge100ST connected to eBridge800E installation:a. Secure unit to desired mounting surface with a proper fastening device utilizing the case’s mounting hole. Unit should be mounted in proximity of camera/device.b. Connect structured cable from IP camera/device to RJ45 jack marked [10/100BaseT] (Fig. 2, pg. 4).c. eBridge1PCTX/eBridge100TM: Connect Coax cable to BNC connector marked [Coax] (Fig. 2, pg. 4).eBridge1ST/eBridge100STR: Connect Coax cable to flying RG6 marked [Coax] (Fig. 2, pg. 4).7. When batteries are not used, a loss of AC will result in the loss of output voltage. When the use of stand-by batteries is desired, they must be lead acid or gel type.Connect four (4) 12VDC batteries wired in series to terminals marked [+ BAT --- ] (Fig. 2, pg. 4), carefully observing polarity.Note: The eBridge is designed to accommodate Megapixel, HD720, HD1080 and VGA (SD) cameras. It is important to note that some high resolution and high frame rate camerasmay demand faster headend processing ability, such as a PC graphics card to present a quality image. If the headend processing equipment is insufficient in speed, the image may showpixilation and latency. It is advisable to pretest system if unsure. Alternatively, frame rate and resolution may be reduced to accommodate system equipment.Technical Specifications:Parameter DescriptionConnections BNC for Coax link. RJ45 for ethernet link.Input power requirements 115VAC, 60Hz, 3.25A or 230VAC, 50/60Hz, 2.0AIndicatorsBlue: Coax Link.Yellow (RJ45 connector): On - Link, Off - No Link, Blinking - Activity.Green (RJ45 connector): On - 100Base-TX, Off - 10Base-T.Green: Power.Environmental ConditionsOperating Ambient Temperature: -10ºC to 50ºC (14ºF to 122ºF).Relative humidity: 85%, +/- 5%Storage Temperature: -30ºC to 70ºC (-22ºF to 158ºF).Operating Altitude: -304.8 to 2,000m.Regulatory Compliance UL/cUL Listed for Information Technology Equipment (UL 60950-1). CE approved.The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of an insulated DANGEROUS VOLTAGE within theproduct’s enclosure that may be of sufficient magnitude to constitute an electric shock.The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literatureaccompanying the appliance.CAUTION: To reduce the risk of electric shock do not open enclosure.There are no user serviceable parts inside. Refer servicing to qualified service personnel. |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine