Manuals database logo
manualsdatabase
Your AI-powered manual search engine

norxe P1 User Manual

Also see for P1: Communication User Guide

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Introduction
  4. Copyright © and Legal Information
  5. Safety and General Information
  6. Service
  7. Packaging
  8. Unpacking
  9. Getting to know the projector
  10. Projector Keypad
  11. Remote Control
  12. Connectivity
  13. User Interface
  14. Main Menu
  15. Source Menu
  16. Status Menu
  17. Night Vision Menu
  18. Lens Options
  19. Basic Setup & Installation
  20. Mounting
  21. Accessory Interface Fixing Points
  22. Locking Zoom & Focus
  23. Lens Adjustment
  24. Advanced Setup & Installation
  25. Top/Bottom Input
  26. D (Active) Input
  27. All Rights Reserved
  28. Maintenance
  29. Technical Data
  31. Optical
  32. Environmental Conditions
  33. Environmental Standards
  34. Technical Data, Projection Lenses
norxe P1 User Manual Manual pdf 13 page image
© All Rights Reservedwww.norxe.comP1 User GuidePage 13 of 408.3 Remote ControlThe projector is supplied with a Remote Control. The Remote Control can be used in infrared (IR) mode or inwired mode. A wired lead with 3.5 mm Jack terminations is required for the latter mode of operation (wired leadnot supplied as standard).Remote Control functionality mirrors that of the projector keypad.8.4 Status Indicator Light Modes of OperationThe Status Indicator Light and LCD are integral to the projector Keypad. They are both positioned adjacent to theLAUNCH (power on / off) button. The status indicator light is used to display projector status, the LCD is used todisplay related additional information in certain circumstances.Status Indicator Light Modes of Operation- PERMANENT AMBER LIGHT: The projector light source is off. The projector is in standby / ready mode.- PERMANENT GREEN LIGHT: The projector light source is on. The projector is active.- PERMANENT RED LIGHT: Over temperature. Projector shut down (to standby).- FLASHING AMBER LIGHT: The projector is in a transitional state between standby and active or alternativelybetween active and standby.- FLASHING RED LIGHT: Critical error and / or one or more cooling fans not working properly.NOTE! - Critical error cause dependent the projector may shut down (to standby) and restart. It isnormal for the Status Indicator to flash red during this process.NOTE! - Projector will shut down if over temperature.LCD Modes of Operation- ‘Warming up …’ Additional information message displayed in conjunction with flashing yellow statusindicator light.- ‘Shutting down …’ Additional information message displayed in conjunction with flashing yellow statusindicator light. Message is displayed for approximately 2 minutes. The projector light source cannot berestarted during this timeframe.
/ 40
Related manuals for norxe P1
norxe P1 Communication User Manual first page preview
norxe P1 Communication User Manual
This manual is suitable for:
P1
Manuals database logo
manualsdatabase
Your AI-powered manual search engine