IBM 6400-I10 manuals
6400-I10
Table of contents
- line matrix printers
- Table of Contents
- Table Of Contents
- communication notices
- electrical safety
- safety notices
- BASIC OPERATING PROCEDURES
- Table Of Contents
- Powering On the Printer
- Using the Operator Panel
- printer configuration
- line feed
- form feed
- standard mode
- Power Paper Stacker Option
- Changing the Paper Exit Location (Pedestal Models Only)
- Loading Paper
- Reloading Paper
- Unloading Paper
- Unloading the Power Stacker
- Setting Top-of-Form
- setting top of form
- Replacing the Ribbon
- Canceling a Print Job
- Parameters and Configurations
- Saving Configurations
- Recalling Configurations
- Deleting Configurations
- The Power-On Configuration
- Protecting Custom Sets
- Printing Configurations
- Operator Print Tests
- Clearing Paper Jams
- Cleaning the Printer
- Solving Printer Problems
- Status and Fault Messages
6400-I10
Table of contents
- safety notices
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Introduction
- Conventions In This Setup Guide
- Related Documents
- The IBM 6400 Printer Family
- Standard Capabilities
- output control
- Optional Features
- Protocols And Emulations
- Installation
- Before You Begin
- Select A Site
- Printer Dimensions
- Printer Component Locations
- Remove Shipping Restraints (Cabinet Model)
- Remove The Cardboard Packing And Envelope
- Remove The Hammer Bank Protective Foam
- Remove The Platen Protective Foam
- Remove Wood Blocks
- Adjust The Paper Supports
- Release The Paper Chains (Cabinet Model)
- Remove Tags (Cabinet Model)
- Remove The Shipping Restraints From The Power Paper Stacker
- Removing Shipping Restraints (Pedestal Model)
- Remove The Hammer Bank And Protective Foam
- Attach The Input Paper Shelf and Output Basket
- Remove Tags - Pedestal Model
- Setting Top Paper Exit
- Setting Rear Paper Exit
- Connect The Interface And Power Cables (Cabinet Models)
- Connect The Interface And Power Cables (Pedestal Models)
- Attach The Operator Panel Overlay Label
- Install The Ribbon
- Load The Paper
- Power Paper Stacker Option
- Setting Up The Power Paper Stacker
- Loading And Starting The Power Paper Stacker
- Checking The Paper Feed
- Set The Top-of-Form
- Test The Printer
- Configuring the Printer
- Active Versus Saved Configurations
- Using The Operator Panel
- Program Mode
- Entering Program Mode
- Factory Default Configuration Values
- Changing Parameters
- Saving Your Configuration In A Custom Set
- Loading Custom Sets Or Factory Default Values
- Changing The Power On Configuration
- The Configuration Menus
- Main Menu
- Printer Control Menu
- Configuration Management Menu
- Twinax Interface Menu
- Coax Interface Menu
- Compatibility Options Menu
- Interface Menu
- Network Setup Menu
- Adapter Parameters Submenu
- Ethernet Address Submenu
- Ethernet Parameters Submenu
- Wireless Address Menu
- Wireless Parameters Menu
- Parallel Interface Menu
- PC Parallel Menu
- Dataproducts Menu
- IEEE 1284
- Serial Interface Menu
- Emulation Configuration Menu
- IPDS Feature
- IPDS Configuration Menu
- ANSI
- IGP Feature (PGL)
- IGP Emulation Menu
- Code V Feature (VGL)
- Code V Emulation Menu
- Printer Emulation Configuration Menu
- Proprinter III XL Emulation Menu
- Epson Emulation Menu
- P-Series Emulation Menu
- P-Series XQ Emulation Menu
- Serial Matrix Emulation Menu
- Print Format Menu
- Operator Print Tests Menu
- Printer Information Menu
- RibbonMinder Menu
- Printer Interfaces
- RS-232 And RS-422 Serial Interfaces
- RS-422
- RS-232 Serial Interface Protocols
- RS-232 and RS-422 Serial Interface Error Handling
- PC Parallel Interface
- PC Parallel Interface Signals
- PC Parallel Interface Configuration
- Dataproducts Parallel Interface
- Dataproducts Parallel Interface Signals
- IEEE 1284 Parallel Interface
- The Negotiation Phase
- Terminating Resistor Configurations
- removal and installation
- Routine Service and Diagnostics
- Cleaning Inside The Cabinet
- Printer Self –Tests
- Running The Printer Self–Tests
- Hex Code Printout
- Fault Messages
- Ribbon Specifications
- Ordering Ribbons
- Paper Specifications
- Labels
- Environmental Characteristics
- Electrical Characteristics
- Interfaces
- Printing Rates
- power consumption
- Character Formation
- Printing Speed
- C Host Attachment
- Compatibility and Limitations
- Limitations
- Attaching Printer to an iSeries or zSeries Host System
- Changing Your iSeries Printer Configuration
- Attaching Printer to Remote Control Unit with Twinax Interface
- Attaching Printer to an IBM System/36 with Twinax Interface
- Attaching Printer to zSeries Systems
- LU1-SCS-Remote SNA 3174 Control Unit
- LU3-DSE-Local SNA 3174 Control Unit
- LU3-DSE-Remote SNA 3174 Control Unit
- LU0-DSC-Local Non-SNA 3174 Control Unit
- Attaching Printer to VM Host System
- Non-SNA Attachment
- Summary of LU Types and Representative IBM Products
- Notices
- Trademarks
- Product Recycling and Disposal
- Communication Statements
- industry canada compliance statement
- german conformity statement
- Glossary
manualsdatabase
Your AI-powered manual search engine