ABB ACS800-17 manuals
ACS800-17
Table of contents
- What this chapter contains
- Installation and maintenance work
- Grounding
- Fibre optic cables
- Operation
- Permanent magnet motor drives
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table of contents
- Contents
- Installation and commissioning flowchart
- Inquiries
- Frame R6
- Frame R7i
- Frame R8i
- Swing-out frame
- Cabling direction
- Single-line circuit diagram of the drive
- Operation principle
- Motor-side converter
- Controls
- Door switches
- Control panel
- Fieldbus control of the line-side converter
- Type code
- Frame sizes 2×R8i to 6×R8i
- Moving the unit
- by fork-lift or pallet truck
- Final placement of the unit
- Before installation
- Installation procedure
- Fastening the cabinet to the floor (Non-marine units)
- Holes inside the cabinet
- Fastening the unit to the floor and wall (Marine units)
- Joining the shipping splits
- Connecting the DC busbars and the PE busbar
- DC busbars
- Miscellaneous
- Cooling air intake through bottom of cabinet
- Electric welding
- Protecting the motor insulation and bearings
- Permanent magnet synchronous motor
- Earth fault (Ground fault) protection
- Prevention of unexpected start-up
- Safe torque off
- Selecting the power cables
- Alternative power cable types
- Motor cable shield
- Power factor compensation capacitors
- Before opening an output contactor (in DTC motor control mode)
- Selecting the control cables
- Connection of a motor temperature sensor to the drive I/O
- Control cable ducts
- Electrical installation
- EMC filter +E200
- Input power connection – Frame R6
- Input power connection – Frame R7i
- Input power connection – Frame R8i
- Input power connection – Frame 2×R8i and up
- Grounding of shielded single-core input cables
- Motor connection – Frame R7i
- Motor connection – Frame R8i units without option +E202 or +H359
- Motor connection – Frame R8i with option +E202 but without +H359
- Motor connection – Units with common motor terminal cubicle (+H359)
- Motor connection – Frame 2×R8i and up without common motor terminal cubicle
- Connection procedure
- Control connections
- Installation of optional modules and PC
- Tap settings of the auxiliary voltage transformer (Frame R8i and up)
- External control connections (non-US)
- External control connections (US)
- RMIO board specifications
- Relay outputs
- Start-up procedure
- Starting the supply unit
- ACS800-17-specific parameters in the IGBT Supply Control Program
- Parameters
- Default values of parameters with the ACS800-17
- ACS800-17-specific parameters in the inverter control program
- the inverter control program
- Reduced run capability
- Quick connectors (Frame R8i and up)
- Cooling fans
- Supply/Inverter module cooling fan replacement (Frame R7i)
- LCL filter module cooling fan replacement (Frame R7i)
- Supply and inverter module cooling fan replacement (Frame R8i and up)
- LCL filter cooling fan replacement (Frame R8i and up)
- Cabinet fan replacement (Frame R6)
- Cabinet fan replacement (Frame 2xR8i and up with IP21-42)
- Cabinet fan replacement (Frame R8i and up with IP54)
- Heatsinks
- Power module replacement (Frame R8i and up)
- Extracting the module from the cubicle
- Inserting the module into the cubicle
- Faults and warnings displayed by the CDP-312R Control Panel
- LEDs of the drive
- Symbols
- Temperature derating
- NEMA ratings
- AC fuses
- DC fuses
- Input power connection
- Motor connection
- Efficiency
- Materials
- Tightening torques for power connections
- CE marking
- Declaration of Conformity
- Compliance with EN 61800-3:2004
- Category C4
- Frame R7i with +E202/+E205/+H359
- Frame R7i, marine construction (+C121)
- Frame R8i with +E202/+H359
- Frame 2×R8i
- Frame 3×R8i
- Frame 4×R8i
- Frame 5×R8i
- Frame 6×R8i
manualsdatabase
Your AI-powered manual search engine