ABB ACS880-07XT Series manuals
ACS880-07XT Series
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Contents of this chapter
- General safety in installation, start-up and maintenance
- Electrical safety in installation, start-up and maintenance
- Additional instructions and notes
- Grounding
- Additional instructions for permanent magnet motor drives
- Related manuals
- Quick installation, commissioning and operation flowchart
- Terms and abbreviations
- Safety data (SIL, PL)
- Overview circuit diagram of the drive
- pulse connection (option +A004)
- Cabinet line-up and layout examples
- Overview of power and control connections
- Door switches and lights
- Main disconnecting device (Q1.1)
- Control panel
- Descriptions of cabinet options
- Terminals for external control voltage (option +G307)
- Pt100 relays (options +2L506, +3L506, +5L506, +8L506)
- Type designation label
- Necessary tools
- Moving and unpacking the drive
- Lifting the crate with a crane
- Moving the crate with a forklift
- Removing the transport package
- Moving the cabinet on rollers
- Fastening the cabinet to the floor and wall or roof (non-marine units)
- Fastening methods
- Fastening the cabinet to the floor and roof/wall (marine units)
- Miscellaneous
- Selecting the supply disconnecting device
- Protecting the motor insulation and bearings
- Requirements table
- Additional requirements for explosion-safe (EX) motors
- Additional requirements for non-ABB high-output and IP23 motors
- Additional data for calculating the rise time and the peak line-to-line voltage
- Selecting the power cables
- Typical power cable sizes
- Alternative power cable types
- Motor cable shield
- Signals in separate cables
- Separate control cable ducts
- Implementing thermal overload and short-circuit protection
- Protecting the motor against thermal overload
- IImplementing the Power loss ride-through function
- Using a contactor between the drive and the motor
- Example bypass connection
- Switching the motor power supply from direct-on-line to drive
- Motor and motor cable
- Connecting the control cables
- Routing the control cables inside the cabinet
- Connecting a 230/115 V AC auxiliary voltage supply (UPS, option +G307)
- Wiring the thermistor relay(s) (options +L505 and +2L505)
- Wiring the Pt100 relays (options +2L506, +3L506, +5L506 and +8L506)
- Powering the heating(options +G300)
- Connecting the motor cables (units without common motor terminal)
- Connecting the motor cables (units with du/dt and common motor terminal)
- Connecting the input power cables
- Connection procedure
- Connecting a PC
- Installing option modules
- Mechanical installation of an FSO-xx safety functions module
- Wiring of optional modules
- What this chapter contains
- Control unit layout and connections
- Default I/O diagram of the control unit (A41)
- External power supply for the control unit (XPOW)
- AI1 or AI2 as a Pt100, Pt1000 or KTY84 sensor input
- Safe torque off (XSTO, XSTO OUT)
- Control unit connector data
- Checks/Settings with no voltage connected
- Setting up the supply unit parameters
- Cabinet
- Cleaning the door air inlets (IP54)
- Heatsink
- Fans
- Replacing the drive module main fans
- Replacing a roof fan (IP54)
- Replacing the drive module
- Replacing the left module
- Capacitors
- Control units
- Control unit battery
- Reduced run
- Ambient temperature derating
- Altitude derating
- High speed mode
- Frame sizes and power module types
- Dimensions and weights
- Electrical power network specification
- Efficiency
- Materials
- Applicable standards
- Tightening torques
- Disclaimers
- Category C2
- Cabinet line-up dimensions
- Dimension drawing examples
- Location of input terminals (ACS880-07XT-1310A-5, ACS880-07XT-1320A
- Location of output terminals (ACS880-07XT, R10, with du/dt)
- Location of output terminals (ACS880-07XT, R10, without du/dt)
- Location of output terminals (ACS880-07XT, R11, with du/dt)
- Location of output terminals (ACS880-07XT, R11, without du/dt)
- Location of PE terminals (ACS880-07XT)
- Location of resistor terminals (ACS880-07XT, R10)
- Location of resistor terminals (ACS880-07XT, R11)
- Selecting a custom resistor
- Maximum cable length
- Mechanical installation of external brake resistors
- Technical data
- Product and service inquiries
Related products
ACS880 SeriesACS880-01 SeriesACS880 P940 SeriesACS880 P944 SeriesACS880-01+C135 SeriesACS880-31SeriesACS850-04 seriesACS580 SeriesACS850 seriesACS380 SeriesABB categories
Industrial Equipment
DC Drives
Controller
Relays
Measuring Instruments
Circuit breakers
Battery Charger
Industrial Electrical
Transformer
Switch
manualsdatabase
Your AI-powered manual search engine