Advantech AIMB-585 manuals
AIMB-585
Table of contents
- declaration of conformity
- ordering information
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Chapter 1 General Information
- Introduction
- Input/Output
- Jumpers and Connectors
- Board layout: Jumper and Connector Locations
- Figure 1.2 I/O Connectors
- Safety Precautions
- CMOS Clear (CMOS1)
- JUSBPWR1-2 (USB Power Selection Connector)
- JSETCOM2: COM2 RS232, RS422, RS485 Selection
- JCASEOP_SW1: Case Open Selection Pin Header
- Cache Memory
- USB Power Switch (JUSBPWR1/JUSBPWR2)
- COM1/DVI-D Connector (COM1+DVI 1) Connector
- Serial Ports (COM1~COM6)
- Display Port (DP1)
- PS/2 Keyboard and Mouse Connector
- System FAN Connector (SYSFAN1/2/3/4)
- Front Panel Connectors (JFP1/JFP2)
- Power LED and keyboard lock connector (JFP2/PWR_LED & KEY LOCK)
- Digital Audio Connector (SPDIF_OUT1)
- Serial ATA Interface (SATA1 ~ SATA4)
- pin Alarm Board Connector (VOLT1)
- Front Panel Audio Connector (FPAUD1)
- ATX Power Connector (EATXPWR1, ATX12V1)
- VGA (VGA1)
- General purpose I/O Connector (GPIO1)
- eDP Connector (eDP1)
- Chapter 3 BIOS Operation
- Main Menu
- Advanced BIOS Features
- Chipset Configuration Setting
- System Agent (SA) Configuration
- PCH-IO Configuration
- Security Setting
- Boot Setting
- Save & Exit Configuration
- Software Utility
- Before You Begin
- Windows 8 Driver Setup
- Chapter 6 VGA Setup
- Chapter 7 LAN Configuration
- Windows® 8 Driver Setup (Intel I219LM/ Intel I211AT)
- A.1 Programming the Watchdog Timer
- Table A.1: Watchdog Timer Registers
- A.1.3 Example Program
- B.1 Keyboard & Mouse connector (KBMS1)
- B.3 COM1 connector (COM1)
- B.5 DisplayPort1(Up) + HDMI1(Down) stack connector (DP1+HDMI1)
- B.6 Universal Serial Bus Port 5 / 6 / 11 / 12 (USB561112)
- B.7 RJ45 + USB3.0 stack connector (LAN1_USB12)
- B.8 RJ45 + USB3.0 stack connector (LAN2_USB34)
- B.9 USB Power selection header #2 (JUSBPWR2)
- B.12 Audio amplifier output pin header (JAMP1)
- B.14 Embedded DisplayPort (EDP1)
- B.16 EDP Backlight inverter power connector (INV1)
- B.18 Dual port USB3.0 header (USB910)
- B.20 COMS Mode selection (JCOMS1)
- B.22 System Fan #2 connector (SYSFAN2)
- B.25 Power LED and keyboard lock pin header (JFP2)
- B.28 AT/ATX Mode selection (PSON1)
- B.30 Serial ATA interface connector (SATA1 / SATA2 / SATA3 / SATA4)
- B.31 MINIPCIE, mSATA connector (MINIPCIE1)
- B.32 CMOS battery connector (BAT1)
- B.34 COM3 ~ COM6 box header (COM3456)
- B.35 ATX 24pin power connector (EATXPWR1)
- B.37 COM2 box header (COM2)
- B.39 COM2 RS232,RS422,RS485 selection pin header (JSETCOM2)
- B.41 Case Open connector (JCASE1)
- B.44 System Fan #1 connector (SYSFAN1)
- Table B.47:USB VBUS selection for LAN1_USB12, LAN2_USB34 USB561112 (JUSBPWR2)
- B.49 Voltage selection for EDP1 connector (JEDP1)
- B.51 PWRBTN#/ RESET#/HDD LED / Serial bus from HW monitor IC/Internal Buzzer / External Speaker header (JFP1)
- B.53 AT / ATX Mode selection (PSON1)
- B.55 Case open selection pin header (JCASEOP_SW1)
manualsdatabase
Your AI-powered manual search engine