TDK-Lambda Genesys Series manuals
Genesys Series
Table of contents
- Table Of Contents
- Table Of Contents
- list of figures
- THE DIGITAL (IEEE 488.2 SCPI) PROGRAMMING OPTION
- USING DIGITAL PROGRAMMING
- CONFIGURING THE IEEE INTERFACE
- CONFIGURING THE SUPPLIES
- EXAMPLE PROGRAM WRITTEN IN VISUAL BASIC
- EXAMPLE PROGRAM WRITTEN IN LABVIEW
- PROGRAMMING COMMANDS
- READ PROGRAMMED VOLTAGE COMMAND
- MEASURE CURRENT COMMAND
- GO TO REMOTE MODE COMMAND
- GLOBAL PROGRAM OUTPUT VOLTAGE
- GLOBAL SAVE POWER SUPPLY SETTINGS COMMAND
- CURRENT FOLD BACK PROTECTION
- OPERATING CONDITION COMMANDS
- REPORT POWER SUPPLY POWER-UP MODE COMMAND
- READ SERVICE REQUEST ENABLE COMMAND
- READ STANDARD EVENT STATUS 'EVENT' REGISTER COMMAND
- OPERATION COMPLETE COMMAND
- INSTRUMENT SELECT COMMANDS
- SET OPERATIONAL CONDITION 'ENABLE' REGISTER COMMAND
- SET QUESTIONABLE CONDITION 'ENABLE' REGISTER COMMAND
- READ QUESTIONABLE INSTRUMENT SUMMARY 'EVENT' REGISTER COMMAND
- CLEAR ALL STATUS REGISTERS
- STANDARD EVENT STATUS 'EVENT' REGISTER
- the summary registers
- SYSTEM:ERROR MESSAGES
- service request
- output queue
- NOTES
Genesys Series
Table of contents
- Table Of Contents
- WARRANTY
- General Information
- Specifications
- Linking Genesys™ USB To Other Genesys™ Supplies
- Required Equipment
- Install USB Drivers for a Virtual COM Port
- Communicating Using a Virtual COM Port
- Find the Assigned COM Port
- Open the Assigned COM Port
- Get the Power Supply Address
- Start Typing Commands
- Linking Multiple Supplies
Genesys Series
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- WARRANTY
- SAFETY INSTRUCTIONS
- consignes de securite
- norme di sicurezza
- GENERAL INFORMATION
- Accessories
- Model Number Format
- SPECIFICATIONS
- Protective Functions
- Remote Analog Control And Signals
- Front Panel
- Digitial Programming And Readback
- Safety
- J1 Connector
- INSTALLATION
- Rack Mounting
- Turn-On Checkout Procedure
- Connecting the Load
- Local and Remote Sensing
- Repackaging for Shipment
- FRONT AND REAR PANEL CONTROLS AND CONNECTORS
- Rear Panel Connections and Controls
- Rear Panel SW1 Setup Switch
- Rear Panel J1 Programming and Monitoring Connector
- LOCAL OPERATION
- Over Voltage Protection (OVP)
- Under Voltage Limit (UVL)
- Output ON/OFF Control
- Enable/Disable Control via Rear Panel J1 Connector
- Safe Start and Auto-Restart Modes
- Over Temperature Protection (OTP)
- SERIES AND PARALLEL OPERATION
- Parallel Operation (Single-Wire/Two-Wire Method)
- REMOTE AND ANALOG PROGRAMMING
- Local/Remote Analog Indication
- Resistive Programming of Output Voltage and Current Limit
- Remote Monitoring of Output Voltage and Current
- RS-232 & RS-485 REMOTE CONTROL
- Rear Panel RS-232/RS-485 Connector
- Connecting Power Supplies to the RS-232 or RS-485 Bus
- Communication Interface Protocol
- Error Messages
- Command Set Description
- Global Output Commands
- Fast Queries
- Status and Error Commands
- Status, Error, and SRQ Registers
- Serial Communication Test Set-Up
- ISOLATED ANALOG PROGRAMMING OPTION
- Isolated Programming & Monitoring Connector
- Setup and Operating Instructions
- MAINTENANCE
Genesys Series
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- GENERAL INFORMATION
- Feature Summary
- SPECIFICATIONS
- LAN Command Speed
- SELECT THE CONTROL METHOD
- LAN Option Rear Panel View
- CONNECT TO NETWORK
- Power-up the LAN Power Supply
- IP Addresses
- Description and DNS Service Names
- LAN SETUP
- LAN Reset
- Default LAN Settings
- Benefit of Web
- The HOME
- Logging In
- DC Power
- HELP
- PROGRAMMING USING VISA DRIVERS
- PROGRAMMING USING IVI DRIVERS
- PROGRAMMING USING SOCKETS
- Input Buffer Requirements
- Message Terminators
- CONNECTING OVER WAN
- SCPI COMMAND REFERENCE
- Configuring the Output
- Measuring the Output
- Operating Modes
- Output Protection
- LAN Specific Commands
- Common Commands
- Error and Status Commands
- Figure 7. Error and Status Registers
- RS-485 MULTI-DROP COMMANDS
- Configure the LAN Supply
- Multi-drop Programming Using SCPI Commands
- SYSTEM:ERROR? MESSAGES
- SAMPLE PROGRAMS
- TROUBLESHOOTING
- Cannot Communicate to the Power Supply
- Web Page "Refresh List" Does Not Find Slave Supplies
- GLOSSARY
Related products
350S24 SeriesPAH300 SeriesG/P-3U-10VG/P-2U-10VG/P-4U-10-40VG/P-2U-20-40VG/P-6U-60-100VG/P-3U-20-40VG/P-3U-60-100VG/P-2U-60-100VTDK-Lambda categories
Power Supply
Media Converter
Network Hardware
Adapter
Cables and connectors
Portable Generator
Recording Equipment
Control Unit
Motherboard
I/O Systems
manualsdatabase
Your AI-powered manual search engine