Daikin RXR50EV1B manuals
RXR50EV1B
Table of contents
- Part 1 List of Functions ................................................................ 1
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- safety cautions
- cautions regarding products after repair
- inspection after repair
- using icons
- Part 1 List of Functions
- Functions
- Part 2 Specifications
- Specifications
- Printed Circuit Board Connector Wiring Diagram
- Outdoor Unit
- Part 4 Function and Control
- Table Of Contents
- Description of Operation
- Main Functions
- Comfort Sleep Operation
- MOISTURIZING Operation
- Automatic Operation
- Comfort Airflow Mode
- Cooling Breeze Operation
- Power-airflow Dual Flaps
- Wide-angle Louvers
- D Airflow
- POWERFUL Operation
- Indoor Unit Quiet Operation
- Monitor Brightness Setting
- MOLD PROOF Operation
- Mold Proof Stick
- MOLD SHOCK Operation
- HOME LEAVE Ventilation
- FLASH STREAMER AIR PURIFYING Operation
- Fresh Air Supply Ventilation
- Wipe-clean Flat Panel
- TIMER Operation
- Night Set Mode
- Table for Special Modes
- Thermostat Control
- Fan Speed Control for Indoor Units
- Draft Prevention (HOT Start)
- Control Specification
- Preheating Operation (Quick Warming Function)
- Four-way Valve Operation
- Compressor Start up Protection
- Fan Speed Control for Outdoor Unit
- Input Current Control
- Peak-cut Control
- Indoor Coil Freeze-up Protection
- Dew Prevention
- Liquid Compression Protection 2
- Discharge Pipe Temperature Control
- Automatic Defrosting
- Electronic Expansion Valve Control
- Installation Manual
- choosing an installation site
- system configuration
- installation tips
- how to replace the drain plug and drain hose
- indoor unit installation
- drain piping
- refrigerant piping work
- Outdoor Units
- outdoor unit installation drawings
- installation guidelines
- outdoor unit installation
- purging air and checking gas leakage
- pump down operation
- test run and final check
- System Configuration
- Instruction
- Names and Functions of Parts
- Preparation before Operation
- to set the clock
- cooling operation
- heating operation
- AUTO / MOISTURIZING Operation
- COMFORT SLEEP / POWERFUL Operation
- set up
- MOLD SHOCK Operation / INFORMATION DISPLAY
- Care and Cleaning
- cleaning the air filter
- before a long idle period
- Troubleshooting
- check again
- call the service shop immediately
- Service Diagnosis
- Table Of Contents
- Table Of Contents
- Convenient Service Check Function
- Error Code Indication by Remote Controller
- Air conditioner does not run
- Air conditioner runs but does not get cooling (heating)
- When operation starts, safety breaker works
- Air conditioner makes big noise and vibration
- Air does not humidified enough
- Indoor Unit PCB Fault
- Peak-cut Control or Freeze-up Protection
- Fan Motor System (DC Motor) Fault
- Streamer Unit Fault
- Thermistor System Fault
- Front Panel Open / Close Fault
- Humidity Sensor Fault
- Signal Transmission Error (Indoor Unit - Outdoor Unit)
- Incompatible Power Supply between Indoor Unit and Outdoor Unit
- Incomplete Setting for Hose Length
- Outdoor Unit PCB Fault
- Compressor Lock
- DC Fan Lock
- Input Over Current Detection
- Four Way Valve Fault
- High Pressure Control in Cooling
- Compressor Sensor System Fault
- Damper Fault
- Position Sensor Fault
- DC Voltage / DC Current Sensor Fault
- Abnormal Temperature in Electrical Box
- Temperature Rise in Radiation Fin
- Output Overcurrent
- Insufficient Gas
- Over Voltage Protection / Low Voltage Protection
- Outdoor Unit PCB Fault or Communication Circuit Fault
- Signal Transmission Error on Outdoor Unit PCB
- Fan Motor System Fault / Fan Lock
- Heater Wire Fault
- Humidification Fan Outlet Thermistor Fault Abnormal Heater Temperature
- Lights-out of Microcomputer Status Lamp
- Check
- Installation Condition Check
- Power Supply Waveform Check
- Main Circuit Electrolytic Capacitor Check
- “Inverter Checker” Check
- Power Transistor Check
- Discharge Pressure Check
- Electronic Expansion Valve Check
- Indoor Unit PCB Output Check
- Rotating Pulse Input on Outdoor Unit PCB Check
- Humidity Sensor Check
- Four-way Valve Performance Check
- Solenoid Valve for Dehumidification Check
- Indoor Unit
- Removal of the Upper Panel
- Removal of the Front Grille
- Removal of the Assembly of the Open/Close Mechanism
- Removal of the Assembly of the Reduction Motor
- Removal of the Electrical Box
- Removal of the PCB
- Removal of the Dehumidifying Solenoid Valve Coil
- Removal of the Connecting Duct
- Removal of the Drain Hose
- Removal of the Swing Motor
- Removal of the Heat Exchanger
- Removal of the Propeller Fan / Fan Motor
- Removal of Horizontal Blades / Vertical Blades
- Removal of the Streamer Unit
- Removal of the Humidify Unit
- Removal of the Heater Assembly / Humidifying Rotor Moisture Absorption Element) / Humidifying Rotor Motor
- Removal of the Humidifying Assembly
- Removal of the Moisture Absorption Fan Motor
- Removal of the Duct in Humidifier
- Removal of the Sound Blanket
- Remove the Thermistor Assembly
- Removal of the Reactor / Partition Plate
- Removal of the Four Way Valve
- Removal of the Expansion Valve
- Removal of the Compressor
- Part 8 Others
- Others
- Field Setting
- Part 9 Appendix
- Piping Diagrams
- Wiring Diagrams
manualsdatabase
Your AI-powered manual search engine