Dell SC4020 manuals
SC4020
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- About this Guide
- About the SC4020 Storage System
- Storage Center Architecture Options
- Storage Center Communication
- Back-End Connectivity
- System Administration
- SC4020 Storage System Back-Panel Features and Indicators
- SC4020 Storage System Storage Controller Features and Indicators
- SC4020 Storage System Drives
- SC200/SC220 Expansion Enclosure Overview
- SC200/SC220 Expansion Enclosure Back-Panel Features and Indicators
- SC200/SC220 Expansion Enclosure EMM Features and Indicators
- SC200/SC220 Expansion Enclosure Drives
- SC280 Expansion Enclosure Overview
- SC280 Expansion Enclosure Back-Panel Features and Indicators
- SC280 Expansion Enclosure Drives
- SC280 Expansion Enclosure Drive Numbering
- Install the Storage Center Hardware
- Gather Required Materials
- Electrical Safety Precautions
- Install the Storage System in a Rack
- Installing Hard Drives in a Storage System
- Installing the Hard Drives in an SC280 Expansion Enclosure
- Connect the Front-End Cabling
- Legacy Mode
- Types of Redundancy for Front-End Connections
- Failover Behavior
- Fibre Channel Zoning
- Cabling SAN-Attached Host Servers
- Connecting to iSCSI Host Servers
- Cabling Direct-Attached Host Servers
- Four Servers Connected to Dual 12 Gb 4-Port SAS Storage Controllers
- Controllers
- Two Servers Connected to Dual 12 Gb 4-Port SAS Storage Controllers
- Labeling the Front-End Cables
- Cabling the Ethernet Management Port
- Labeling the Ethernet Management Cables
- Cabling the Embedded Ports for iSCSI Replication
- Cabling the Management Port and Replication Port for iSCSI Replication
- Cabling the Embedded Ports for iSCSI Host Connectivity
- Storage Controllers
- Connect the Back-End Cabling
- Back-End Connections for an SC4020 Storage System Without Expansion Enclosures
- SC4020 Storage System and One SC200/SC220 Expansion Enclosure
- SC4020 Storage System and Two or More SC200/SC220 Expansion Enclosures
- Back-end Connections for an SC4020 with SC280 Expansion Enclosures
- SC4020 and Two SC280 Expansion Enclosures
- Label the Back-End Cables
- Set up Storage Center Software
- Required Documents
- Establish a Serial Connection to the Top Storage Controller
- Configure the Top Storage Controller
- Establish a Serial Connection to the Bottom Storage Controller
- Configure the Bottom Storage Controller
- Start the Storage Center Startup Wizard
- Completing the Storage Center Startup Wizard
- Create Disk Folder
- Add Controller
- Time Settings
- System Setup
- Configure SMTP
- Update Setup
- User Setup
- Configure IO Cards
- Configure Ports
- Generate SSL Cert
- Perform Post-Setup Tasks
- Verify Connectivity and Failover
- Test Storage Controller Failover
- Clean Up Test Volumes
- Next Steps
- Adding Multiple Expansion Enclosures to a Storage System Deployed without Expansion Enclosures
- Cable the Expansion Enclosures Together
- Add the SC200/SC220 Expansion Enclosures to the B-Side of the Chain
- Adding an SC200/SC220 Expansion Enclosure to an SC4020 Deployed with Expansion Enclosures
- Check the Disk Count before Adding an Expansion Enclosure
- Add an SC200/SC220 Expansion Enclosure to the B-Side of the Chain
- Adding an SC280 Expansion Enclosure to an SC4020 Deployed without Expansion Enclosures
- Add the SC280 Expansion Enclosure to the A-Side of the Chain
- Adding an SC280 Expansion Enclosure to an SC4020 Deployed with One SC280 Expansion Enclosure
- Add a Second SC280 Expansion Enclosure to the A-Side of the Chain
- Add a Second SC280 Expansion Enclosure to the B-Side of the Chain
- Removing an Expansion Enclosure from a Chain Currently in Service
- Release the Disks in the Expansion Enclosure
- Disconnect the SC200/SC220 Expansion Enclosure from the B-Side of the Chain
- Removing an SC280 Expansion Enclosure from a Chain Currently in Service
- Disconnect the SC280 Expansion Enclosure from the B-Side of the Chain
- Settings by HBA Manufacturer
- QLogic HBA Cards
- Settings by Server Operating System
- HP-UX 11i
- Microsoft MPIO Settings
- Version 5.x
- SuSE Linux
- Flow Control Settings
- Other iSCSI Settings
- Troubleshooting the Serial Connection to a Storage Controller
- Troubleshooting Storage Center Licenses
manualsdatabase
Your AI-powered manual search engine