Manuals database logo
manualsdatabase
Your AI-powered manual search engine

AAF OptiFlo RC Series Installation, Operation And Maintenance Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. INTRODUCTION
  4. Dust explosions
  5. Electrical hazards
  6. Safety Guards
  7. Sizes
  8. Weights
  9. PRODUCT SHIPMENT
  10. Missing goods
  11. SITE PREPARATION
  12. ASSEMBLY AND INSTALLATION
  13. Products shipped in multiple modular assemblies
  14. Installing the access components
  15. Installation of accessories
  16. Compressed air connections
  17. EXPLOSION VENTS
  18. Explosion Vent Burst Sensor
  19. Servicing
  20. Normal operation
  21. Initial Weekly Maintenance
  22. Six months
  23. Cartridge removal and installation
  24. Accessories
  25. Visible Discharge (emission to atmosphere)
  26. RECOMMENDED SPARE PARTS LIST
AAF OptiFlo RC Series Installation, Operation And Maintenance Manual Manual pdf 20 page image
20GDED-IOM-215-A10 EXPLOSION VENTSThe following only applies to AAF-supplied explosion vents. Additional and/or differentsteps, equipment, etc. may be needed for vents and other equipment not supplied by AAF.Further, the following is a non-exhaustive list of recommendations, and users must carefullyread, among other things, the manufacturer’s explosion vent guide for further instructions.10.1 Installation of the explosion ventIf an explosion vent is ordered with the OptiFlo RC, the explosion vent is shippedseparately from the collector. Ensure no damage has been done to the explosion vent duringshipping or handling.The OptiFlo RC will have a frame constructed as part of the unit where the explosionvent is mounted. The number of explosion vents and location of the explosion vent will bedetailed on the collector drawing.10.2 AssemblyGripping the opposite sides, carefully remove the explosion vent from the crate thatit was shipped. Avoid excessive flexure of the explosion vent while handling.CAUTION: The edges of the explosion vent can be sharp.CAUTION: Incorrect installation of the explosion vent can cause the panel to notopen at the rated burst pressure.Place the explosion vent over the bolt holes of the frame. Make certain the dome isprotruding outwards. Install the outlet frame.Install bolts and washers (x2) and tighten hand tight.
/ 31
Related manuals for AAF OptiFlo 2RC16
AAF RotoClone LVN Installation, Operation And Maintenance Manual first page preview
AAF RotoClone LVN Installation, Operation And Maintenance Manual
AAF AmericanAirFilter K Installation, Operation And Maintenance Instructions first page preview
AAF AmericanAirFilter K Installation, Operation And Maintenance Instructions
This manual is suitable for:
OptiFlo 2RC16OptiFlo 2RC24OptiFlo 2RC4OptiFlo 2RC8OptiFlo 3RC12OptiFlo 3RC24OptiFlo 3RC36OptiFlo 3RC48OptiFlo 3RC6OptiFlo 3RC60OptiFlo 4RC11OptiFlo 4RC16OptiFlo 4RC32OptiFlo 4RC48OptiFlo 4RC64OptiFlo 4RC80OptiFlo 4RC96OptiFlo 5RC100OptiFlo 5RC120OptiFlo 5RC140OptiFlo 5RC160OptiFlo 5RC180OptiFlo 5RC20OptiFlo 5RC40OptiFlo 5RC60OptiFlo 5RC80OptiFlo RC Series
Manuals database logo
manualsdatabase
Your AI-powered manual search engine