Contents - EFFECTIVE: 2018
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table of contents
- What this chapter contains
- General safety in installation, start-up and maintenance
- Electrical safety in installation, start-up and maintenance
- Additional instructions and notes
- Grounding
- Additional instructions for permanent magnet motor drives
- General safety in operation
- Purpose of the supplement
- Layout of option +P940 (IP20, UL Open Type)
- Layout of option +P944 (IP20, UL Open Type)
- Planning the layout of the cabinet
- Arranging the grounding inside the cabinet
- Planning the attaching of the cabinet
- Planning the cooling
- Minimum air inlet and outlet grating sizes
- Installing drives above one another
- Required free space
- Planning the use of cubicle heaters
- Examining the installation site
- Unpacking and examining the delivery (frames R1 to R2)
- Unpacking and examining the delivery (ACS880-11 and ACS880-31 frame R3)
- Unpacking and examining the delivery (ACS880-01 frames R3 to R5)
- Unpacking and examining the delivery (ACS880-01 frames R6 to R9)
- Unpacking and examining the delivery (ACS880-11 and ACS880-31 frames R6 to R9)
- Installing the drive
- Checking the insulation of the assembly
- Power cable connection procedure (IEC)
- Connecting the control cables – ACS880-01 frames R1 and R2
- Installing the drive module shelves and connecting the cables – ACS880-01 frame R3
- Connecting the control cables – ACS880-01 frame R3
- Connecting the control cables – ACS880-01 frames R4 and R5
- Connecting the control cables - ACS880-01 frames R6 to R9
- Degree of protection
- R1 (Option +P940, IP20, UL Open Type)
- R1 (Option +P944, IP20, UL Open Type)
- R2 (Option +P940, IP20, UL Open Type)
- R2 (Option +P944, IP20, UL Open Type)
- R3 (Option +P940, IP20, UL Open Type)
- R3 (Option +P944, IP20, UL Open Type)
- R4 (Option +P940, IP20, UL Open Type)
- R4 (Option +P944, IP20, UL Open Type)
- R5 (Option +P940, IP20, UL Open Type)
- R5 (Option +P944, IP20, UL Open Type)
- R6 (Option +P940, IP20, UL Open Type)
- R6 (Option +P944, IP20, UL Open Type)
- R7 (Option +P940, IP20, UL Open Type)
- R7 (Option +P944, IP20, UL Open Type)
- R8 (Option +P940, IP20, UL Open Type)
- R8 (Option +P944, IP20, UL Open Type)
- R9 (Option +P940, IP20, UL Open Type)
- R9 (Option +P944, IP20, UL Open Type)
- R3 – Option +P940 (IP20, UL Open Type)
- R6 – Option +P940 (IP20, UL Open Type)
- R8 – Option +P940 (IP20, UL Open Type)
|
36 Guidelines for planning the cabinet installationRequired free spaceThe required free space at the top and bottom of the drive module is shown below.The free space is needed for making sure that sufficient cooling air flows through themodule and the module cools correctly.Mounting the control panel on the cabinet doorThe control panel can be mounted on the cabinet door using a DPMP-01 mountingplatform kit (option +J410) or a DPMP-02 (option +J413) mounting platform kit.200 mm (7.87 in)300 mm (11.81 in)DPMP-01 DPMP-02
|
