Contents - EFFECTIVE: 2018
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table of contents
- What this chapter contains
- General safety in installation, start-up and maintenance
- Electrical safety in installation, start-up and maintenance
- Additional instructions and notes
- Grounding
- Additional instructions for permanent magnet motor drives
- General safety in operation
- Purpose of the supplement
- Layout of option +P940 (IP20, UL Open Type)
- Layout of option +P944 (IP20, UL Open Type)
- Planning the layout of the cabinet
- Arranging the grounding inside the cabinet
- Planning the attaching of the cabinet
- Planning the cooling
- Minimum air inlet and outlet grating sizes
- Installing drives above one another
- Required free space
- Planning the use of cubicle heaters
- Examining the installation site
- Unpacking and examining the delivery (frames R1 to R2)
- Unpacking and examining the delivery (ACS880-11 and ACS880-31 frame R3)
- Unpacking and examining the delivery (ACS880-01 frames R3 to R5)
- Unpacking and examining the delivery (ACS880-01 frames R6 to R9)
- Unpacking and examining the delivery (ACS880-11 and ACS880-31 frames R6 to R9)
- Installing the drive
- Checking the insulation of the assembly
- Power cable connection procedure (IEC)
- Connecting the control cables – ACS880-01 frames R1 and R2
- Installing the drive module shelves and connecting the cables – ACS880-01 frame R3
- Connecting the control cables – ACS880-01 frame R3
- Connecting the control cables – ACS880-01 frames R4 and R5
- Connecting the control cables - ACS880-01 frames R6 to R9
- Degree of protection
- R1 (Option +P940, IP20, UL Open Type)
- R1 (Option +P944, IP20, UL Open Type)
- R2 (Option +P940, IP20, UL Open Type)
- R2 (Option +P944, IP20, UL Open Type)
- R3 (Option +P940, IP20, UL Open Type)
- R3 (Option +P944, IP20, UL Open Type)
- R4 (Option +P940, IP20, UL Open Type)
- R4 (Option +P944, IP20, UL Open Type)
- R5 (Option +P940, IP20, UL Open Type)
- R5 (Option +P944, IP20, UL Open Type)
- R6 (Option +P940, IP20, UL Open Type)
- R6 (Option +P944, IP20, UL Open Type)
- R7 (Option +P940, IP20, UL Open Type)
- R7 (Option +P944, IP20, UL Open Type)
- R8 (Option +P940, IP20, UL Open Type)
- R8 (Option +P944, IP20, UL Open Type)
- R9 (Option +P940, IP20, UL Open Type)
- R9 (Option +P944, IP20, UL Open Type)
- R3 – Option +P940 (IP20, UL Open Type)
- R6 – Option +P940 (IP20, UL Open Type)
- R8 – Option +P940 (IP20, UL Open Type)
|
40 Mechanical installationExamining the installation siteThe drive modules can be installed tightly side by side.Make sure that the installation site agrees with these requirements:• The installation site has sufficient ventilation to prevent overheating of the drive.See section Losses, cooling data and noise in the hardware manual.• The operation conditions of the drive agree with the specifications in sectionAmbient conditions in the hardware manual.• The mounting plate is vertical, not flammable and strong enough to hold theweight of the drive module. See section Necessary tools on page 40.• The material below the installation is not flammable.• There is enough free space above and below the drive for cooling air flow, serviceand maintenance. See pages 36 and 72. There is enough free space in front ofthe drive for operation, service and maintenance.Necessary tools• Drill and drill bits• Screwdriver and/or wrench with bits.Moving the drive moduleMove the transport package by pallet truck to the installation site.
|
