ADJ MEGA GO FLOOD BAR User Instructions

Contents

operating modes

MEGA GO FLOOD BAR Operating InstructionsOperating Power:There are two ways to supply power to this unit; battery power or ACpower.• AC Power - To run the unit using AC power, plug the unit into a powersource, and put the Load Switch into the ON position. When using ACpower make sure the Battery Switch is in the OFF position.• Battery Power - To run the unit using Battery power, put the Load andBattery Switches in the ON position.LED Display On/Off:To set the LED display to turn off after 20 seconds, press the MODEbutton until “don” is displayed, press the UP button to display “doff”.Now the display will disappear after 20s. Press any button to turnthe display on again. Be advised though that the display will turn offautomatically after 20 seconds.To set the display press the MODE button until “dXX” is displayed.Use the UP or DOWN buttons to select either:“don” = LED display on at all times.“doFF” = LED display shuts off after 20 seconds.LED Display Inversion:Follow these instructions to flip the display 180° so that the displaycan be read upside down.1. Plug the fixture in and press the MODE button until “dXX” is dis-played. “XX” represents either “on” or “oFF”.2. Press the SET UP button until “Stnd” is displayed.3. Press the UP or DOWN buttons to reverse the display 180°.Operating Modes:The MEGA GO FLOOD BAR has five operating modes:• RGB Dimmer Mode - Choose one of the three colors to remainstatic or adjust the intensity of each color to make your desiredcolor.• Sound-Active mode - The unit will react to sound, chasing throughthe built in programs.• Auto Run Mode - 1 of 16 auto run modes to choose from withadjustable running speed and fade speed.• Static Color Mode - There are 35 colors to choose from.ADJ Products, LLC - www.adj.com - MEGA GO FLOOD BAR User Manual Page 10ADJ Products, LLC - www.adj.com - MEGA GO FLOOD BAR User Manual Page 9Notice: Be sure to follow figures two and three when making your owncables. Do not use the ground lug on the XLR connector. Do not con-nect the cable’s shield conductor to the ground lug or allow the shieldconductor to come in contact with the XLR’s outer casing. Groundingthe shield could cause a short circuit and erratic behavior.MEGA GO FLOOD BAR Set UpDMX512 IN3-PIN XLRPOWER POWER POWERDMX512DMX+,DMX-,COMMON123Termination reduces signal e rrors andavoids signal transmission problemsand interference. It is always advisableto connect a DMX terminal, (Resistance120 Ohm 1/4 W) between PIN 2 (DMX-)and PIN 3 (DMX +) of the last fixture.123123DMX +DMX -COMMONDMX512 OUT3-PIN XLRFigure 2Figure 31 Ground 1 GroundXLR Male Socket XLR Pin Configuration3 Hot2 Cold 2 Cold3 HotXLR Female SocketPin 3 = Data True (positive)Pin 2 = Data Compliment (negative)Pin 1 = GroundSpecial Note: Line Termination. When longer runs of cable areused, you may need to use a terminator on the last unit to avoid erraticbehavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-nected between pins 2 and 3 of a male XLR connector (DATA + andDATA -). This unit is inserted in the female XLR connector of the lastunit in your daisy chain to terminate the line. Using a cable terminator(ADJ part number Z-DMX/T) will decrease the possibilities of erraticbehavior.DMX512 IN3-PIN XLRUNDREMOTECONTROLINPUTPOWERINPUT OUTPUT SOUNDREMOTECONTROLINPUTPOWERINPUT OUTPUT123Termination reduces signal e rrors andavoids signal transmission problemsand interference. It is always advisableto connect a DMX terminal, (Resistance120 Ohm 1/4 W) between PIN 2 (DMX-)and PIN 3 (DMX +) of the last fixture.123Figure 45-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-512 data cables for DATA transmission in place of 3-pin. 5-pin DMXfixtures may be implemented in a 3-pin DMX line. When inserting stan-dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,these adaptors are readily available at most electric stores. The chartbelow details a proper cable conversion.Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)Pin 1Do Not UseDo Not UsePin 3Pin 2Pin 1Pin 3Pin 2Not UsedNot UsedData True (+ signal)Data Compliment (- signal)Ground/Shield3-Pin XLR to 5-Pin XLR Conversion