ADJ ULTRA HEX PAR3 User Instructions
nect the cable’s shield conductor to the ground lug or allow the shieldconductor to come in contact with the XLR’s outer casing. Groundingthe shield could cause a short circuit and erratic behavior.Ultra Hex Par3 Set UpDMX512 IN3-PIN XLRPOWER POWER POWERDMX512DMX+,DMX-,COMMON123Termination reduces signal e rrors andavoids signal transmission problemsand interference. It is always advisableto connect a DMX terminal, (Resistance120 Ohm 1/4 W) between PIN 2 (DMX-)and PIN 3 (DMX +) of the last fixture.123123DMX +DMX -COMMONDMX512 OUT3-PIN XLRFigure 2Figure 31 Ground 1 GroundXLR Male Socket XLR Pin Configuration3 Hot2 Cold 2 Cold3 HotXLR Female SocketPin 3 = Data True (positive)Pin 2 = Data Compliment (negative)Pin 1 = GroundSpecial Note: Line Termination. When longer runs of cable areused, you may need to use a terminator on the last unit to avoid erraticbehavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-nected between pins 2 and 3 of a male XLR connector (DATA + andDATA -). This unit is inserted in the female XLR connector of the lastunit in your daisy chain to terminate the line. Using a cable terminator(ADJ Products, LLC part number Z-DMX/T) will decrease the possibili-ties of erratic behavior.DMX512 IN3-PIN XLRSOUNDREMOTECONTROLINPUTPOWERINPUT OUTPUT SOUNDREMOTECONTROLINPUTPOWERINPUT OUTPUT123Termination reduces signal e rrors andavoids signal transmission problemsand interference. It is always advisableto connect a DMX terminal, (Resistance120 Ohm 1/4 W) between PIN 2 (DMX-)and PIN 3 (DMX +) of the last fixture.123Figure 45-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-512 data cables for DATA transmission in place of 3-pin. 5-pin DMXfixtures may be implemented in a 3-pin DMX line. When inserting stan-dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,these adaptors are readily available at most electric stores. The chartbelow details a proper cable conversion.Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)Pin 1Do Not UseDo Not UsePin 3Pin 2Pin 1Pin 3Pin 2Not UsedNot UsedData True (+ signal)Data Compliment (- signal)Ground/Shield3-Pin XLR to 5-Pin XLR ConversionADJ Products, LLC - www.adj.com - Ultra Hex Par3 User Manual Page 7ADJ Products, LLC - www.adj.com - Ultra Hex Par3 User Manual Page 6Ultra Hex Par3 Operating InstructionsControl Panel Lock:The control panel will lock itself after 30 seconds if nothing ispressed. To unlock the control panel, press the MODE buttonfor 3 seconds.Operating Modes:The Ultra Hex Par3 has five operating modes:• DMX control mode - This function will allow you to control eachindividual fixtures traits with a standard DMX 512 controller such asas the ADJ Show Designer.• RGBWA + UV Mode - Choose one of the six colors to remain staticor adjust the intensity of each color to make your own color.• Sound-Active mode - The unit will react to sound, chasing throughthe built in programs. There are 16 sound active modes.• Auto Mode - There are 33 Auto Modes to choose from. 16 colorfade modes, 16 color change modes, and 1 random mode.• Static Color Mode - There are 63 colors to choose from.DMX Mode:Operating through a DMX controller gives the user the freedom tocreate their own programs tailored to their own individual needs.The Ultra Hex Par3 has 5 DMX modes: 6 Channel mode, 7 Channelmode, 8 Channel mode, 11 Channel mode, and a 12 Channel mode.See pages 14-22 for each modes’ DMX traits.1. This function will allow you to control each individual fixture’straits with a standard DMX 512 controller.2. To run your fixture in DMX mode press the MODE button until“d.XXX” is displayed. “XXX” represents the current displayed ad-dress. Use the UP or DOWN buttons to select your desired DMXaddress, then press the SETUP button to select your DMXChannel mode.3. Use the UP or DOWN buttons to scroll through the DMX Channelmodes. The Channel modes are listed below:• To run the 6 Channel Mode, press the MODE button until “Ch06”is displayed. This is the 6 Channel DMX Mode.• To run the 7 Channel Mode, press the MODE button until “Ch07”is displayed. This is the 7 Channel DMX Mode.• To run the 8 Channel Mode, press the MODE button until “Ch08” |
Related manuals for ADJ ULTRA HEX PAR3
ADJ ULTRA HEX BAR 6 User Instructions
ADJ 5P HEX User Instructions
ADJ Ultra Bar 6 User Instructions
ADJ PRO763 User Instructions
ADJ FLAT PAR TW5 User Instructions
ADJ AGGRESSOR HEX LED User Instructions
ADJ ZIPPER User Instructions
ADJ H2O DMX PRO User Instructions
ADJ 4 STAGE PAK User Instructions
ADJ FLAT PAR QA5XS User Instructions
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine