Acewell ACE-MD085-254 User Manual
ATV/Motorcycle/Scooter ComputerACE-MD085-254/354/5XX User ManualThanks for purchasing the Motorcycle/Scooter/ATV computer; this manual is specificallydesigned for ACE-MD085-25X/354/5XX series. MD085-254 has bar-speedometer up to250Km/H, MD085-354 and MD085-5XX have12000rpm bar-tachometer. Other functionsare the same. Each series includes different models, each model has same functions butwith different LED indicators. You may find that the photo has a set of LED indicatorsdifferent from your computer, the photo is for reference.1. Tachometer Scale 7. Shift warning indicator2. Bar-tachometer 8. RESET Button3. Bar temperature gauge 9. MODE Button4. 1st row: Speedometer 10.Gear Indicator5. 2nd row: Other functions 11. Bar Fuel gauge6. LED Indicators 12. 12/24HR clockFEATURESPANEL DESCRIPTIONSSimultaneously displays tachometer, speedometer, gear indicator, clock, fuelgauge, bar-graph temperature meter and one of the other functions.Integrated an USB connector for Constant voltage control charger.Main unit with Aluminum forging CNC upper ring and built-in 5-7 LED indicatorsfor different applications.Built-in gear indicator which calculates gear comparing speed and RPM, and“gear indicator off” mode for Automatic vehicles.Built-in RGB LED backlight, user can adjust his/her prefer backlight color.On some models the backlight can be controlled separately from the ignitionpower.Bar-graph tachometer has scale of 12,000rpm, digital tachometer is up to19,900rpm.End user is able to adjust odometer when the odometer is less than 30km /18.6miles.Acceleration and deceleration timers as well as distance timer for racingpractice.Built-in air temperature sensor which installed outside the housings.Fast processor so can connect to pulse type gearbox speed sensors.Universal wheel circumference setting range: 1-3999mm.Fuel gauge includes +/- 30 80Ω, 100Ω, 250Ω and 510Ω options for fuelsender input resistance. In reserve mode, the fuel gauge is not displayed andfuel symbol lights when the input wire is connected to -ve. The gauge can beswitched off entirely if not required.Flexible battery warning voltage setting from 11.0 to 14.9V.Speedometer can show nearest 0.1 mph or km/h speed if required by user. E.g.100 or 100.5Includes bracket, RPM sensing wire, speed sensor, PT1/8 temperature sensor,air temperature sensor, fitting kits and wiring harness.Excellent water resistance, anti-vibration structure and noise immunity design.RPM sensor mounting: RPM Input, Either one1. Signal intensity from ignition coil is dependent on vehicle type.2. Coil 2-5 turns around spark plug lead, with more turns creating steadilystronger signal, fewer turns creating weaker signal.3. The RPM circuit is designed for most bikes, however some bikes’ signal is toostrong if the RPM looks like much more than actual RPM and unstable,please connect the included 1M Ohm resistor in series to solve it.SPEED SENSOR Mounting:ACEWELL has several speed sensors; the unit may include one of them. Ifthe model is intended to be connected to a gearbox electronic speed output toobtain the speed reading, no speed sensor will be included.Reed Speed Sensor and Magnet:1. This sensor is universal sensor for motorcycle, find a rotating part to installmagnet (for example disk, sprocket or driveshaft) and a location to installthe sensor where it can be aligned to the magnet.2. Align the center of the magnet to either of the sensor marking lines or theside of the sensor. The magnet must not travel down the body of the sensor3. Installing the sensor parallel to the vibration direction creates optionalanti-vibration effect.4. Make sure the gap between the magnet and the sensor is within 8mm.Hall Effective Speed Sensor and Magnet:1. This is universal sensor for ATV front or rear wheel installation or motorcyclefront wheel installation. For some fitments an accessory speed sensor holdermay need to be purchased.2. Find a rotating part to install magnet (for example disk, sprocket or driveshaft)and a location to install the sensor where it can be aligned to the magnet3. Align the center of the magnet to center of side face of the sensor.4. Make sure the gap between the magnet and the sensor is within 5mSpecific Hall sensors:Cable drive adaptors for most bikes originally fitted with cable drivenspeedometers or milemeters are available. When using these cables it isnecessary to divide the circumference setting by the number of rotations of thecable per rotation of the wheel.Thermo Sensor and Sensor Tube:1. The unit includes a water temperature sensor; you have to purchase a suitablewater pipe temperature sensor tube to install the sensor easily.2. Cut the water pipe, insert the temperature tube into the pipe and secure it byattached pipe clamps.3. Screw the sensor into the tube.4. If your vehicle is fitted with a thermostat that stops water flowing to the radiatorwhen the engine is cold, you will not get a reading until the thermostat opensAir Temperature sensor:1. MD085-5XX series includes an air temperature for outdoor temperaturemeasurement.2. Plug the sensor’s connector to the relative connector from mainSPECIFICATIONSFunctions SpecificationsSymbolSpeedometerDigital TachometerMaximum speedAverage speedMax. RPM Max RPMTrip meter Trip 1/2/3Odometer Odometer12/24 Hour ClockRiding timer R.TimeKm/h / MPHMAX SPDAVG SPD100 19,900 rpm, 100rpm increment100 19,900 rpm, 100rpm increment2.4~300.0 km/h (187.5MPH)2.4~300.0 km/h (187.5MPH)2.4~300.0 km/h (187.5MPH)0.00~999.99 KM/Miles0 - 999999 KM, 0-624999 Miles0:00’00” – 11H59’59” / 23H59’59”0 – 9999H59’0 – 99H59’59”0 – 9999H59’Gear indicator1-5 bars, +/- 30 80Ω, 100Ω, 250Ω,510Ω, off mode or RES mode.8-18VDC, battery voltage warning settable0 180 / 32 356 , off or Hi modes.-20 60 / -4 1400 180 / 32 3561-5 bars or Off mode.Bar-Fuel GaugeN, R, 1, 2,...8 or offTotal Riding TimeHour meter HR Time88:88(AM/PM)Volt meter VOLTEngine TemperatureAir TemperatureMAX Temperature 1/2Bar TemperatureDstTimerAccTimerDstTimerMaintain0 to 1/4 mile. 0 to100Meter, 0 to 400Meter0 to 100km/h, 50 to 70mph100km/h to 0km/h0 9999H / 0 9999Km or Miles adjustableDistance TimerAcceleration TimerDeceleration timerMaintenance reminderMAXTEMP1/2TEMP1TEMP2T.TimePower Input DC 8-18VSpeed Sensor Reed, 2 or 3 wires Hall-effect SensorTachometer input CDI or Ignition Coil Signal or ECUWheel circumference setting 1mm-3999mm (1mm increment)Temperature sensor PT1/8” thermistor sensorAir Temperature sensor Air thermistor sensorDimensions Ø85*56.1mmG r a y W i r eY e l l o w W i r e: Bar-Graphic TachometerThe bar tachometer is 12,000rpm.Km/H or MPH: Speedometer1. Displays speed meter up to 300 Km/H or 187.5 MPH.2. Speedometer can show nearest 0.1 mph or km/h speed if required by user. E.g.99 or 99.93. The maximum frequency of software divider is 7K Hz.4. The speed can be less than 399.9 KM/H in case the setup is using softwaredivider for speedometer, for example the maximum speed is 250KM/H in casesetup of software at 105P and the wheel circumference at 1277mm.RPM: Digital Tachometer1. It displays digital tachometer up to 19,990RPM and displays 19,999rpm whentachometer is over 20,000rpm..2. Tachometer signal can pick up from either CDI or Ignition Coil Signal.Shift Warning RPM1. The function enables you to set up a shift warning RPM.2. Shift warning LED indicator flashes when RPM reaches setting value, and stopsflashing after you shift gear.MAX RPM: Maximum TachometerDisplays highest tachometer achieved since last Reset operation.MAX SPD: Maximum Speed MeterDisplays highest speed achieved since last Reset operation.AVG SPD: Average Speed MeterIt calculates average speed from last RESET. The AVG is calculated from TRIP 1be divided by RT.TRIP 1/2: Trip Meter 1 or 2Trip 1 or Trip 2 function accumulates distance travelled since last RESET.TRIP 3: Trip Meter 31. TRIP-3 function appears and starts to accumulate trip distance meanwhileflashes the last fuel bar automatically at low fuel warning status.2. The LCD screen will auto change to the Trip 3 screen after 4 seconds of buttonoperations at low fuel warning status.3. TRIP-3 be reset to zero automatically when fuel is added to over the low fuelwarning level.Odometer:1. Odometer accumulates total distance traveled.2. Odometer data is adjustable when it is less than 30km (18.6 Miles), after that itstored in memory and cannot be reset.R. Time: Riding Timer1. Calculates total running time since last RESET.2. Counter automatically begins with movement.T. Time: Total Riding Timer1. Calculates total riding time fr om the beginning of the bike.2. TT data is stored in memory, and couldn’t be reset.HR Time: Total Hour Meter1. Calculates total engine operation time since installation.2. Count automatically begins with engine starting.3. HR Time data is stored in memory, and couldn’t be reset.: 12/24 hour ClockIt displays 12 or 24 hour current time.TEMP1: Digital Engine Temperature Meter1. It displays -L- or -L- when temperature is lower than 40 or 104, anddisplays -H- or –H- when temperature is over 180 or 356.2. The LCD screen jumps to TEMP 1 screen automatically, flashes temperaturebar and -H- as well backlight color when the thermo sensor detectstemperature higher than the maximum preset temperature.3. The LCD screen will auto change to the TEMP 1 screen and flashesbar-temperature and -H- after 4 seconds of button operations at overtemperature status. Backlight always flashes at over temperature status.4. Stop engine until temperature cooling down to protect your engine.TEMP 2: Air TemperatureIt displays air temperature from -20(-4 ) to+60(+140)MAXTEMP1/2: Maximum Temperature 1/2*Displays highest temperature achieved since last Reset operation.Maintain: Maintenance Reminders1. It counts down the preset Maintain entered time or distance since last RESET.2. It accumulates Maintain when the count down reaches to “0”, and symbol of“Maintain” flash to remind you to maintain oil or parts.3. Push and hold RESET button to reset and restart the maintenance reminderafter maintained.VOLT: Digital Voltage GaugeIt checks bike’s battery and charging systems health.: Gear Indicator1. The gear indicator has each one wire for N and R, connect wires to N and Rgears firstly.2. The gear indicator calculates gear comparing speed and RPM then displaysgear position.3. User has to training the gear indicator before use it.:Bar Thermometer*1. Have 5 bars to indicate engine temperature.2. The 3rd bar counts from bottom be turned on and over temperature LEDflashes when thermometer reaches the preset warning temperature, each+/-15 lights on/off a bar base on the 4th bar.3. The bar-temperature flashes when the measured temperature is higher thanthe preset warning temperature.:Fuel Gauge1. Has 5 bars to indicate how much fuel remains.2. To use as a fuel gauge, it built-in F10 E250, F10 E510, F30 E80,F100E10,F250E10, F510E10,F80 E30 OFF Ohm fuel sender resistance,FXXX means full fuel resistance, EXXX means empty fuel resistance, the fuelbars will disappear when you select “OFF” mode. Last bar flashes to indicatelow fuel level automatically. F30 E80 and F80 E30 are for vehicle application.3. To use as a reserve indicator, connect the reserve switch to the input and putinto “RES” mode. When the switch pulls the input to –ve the backlight will flashdifferent color and the last fuel-bar flash. On vehicles with temperature basedsensors a 68 ohm 5w resistor needs to be connected between the input wireand 12v (switched)4.If the gauge is not required they can be switched offDstTimer: Distance Test Timer1. The DstTimer can be set 100meter or 400meter.2. The unit calculates trip timer auto- start when receive speed signal and auto-stop when the bike/vehicle reaches the preset distance.AccTimer: Acceleration Timer Test1. The AccTimer can be set 0-100Km/H acceleration test.2. The unit calculates acceleration timer auto- start when receive speed signaland auto- stop when the bike/vehicle reaches the preset speed.DecTimer: Deceleration Timer Test1. The DecTimer can be set 100 to 0Km/H deceleration test.2. The unit calculates deceleration timer auto- start when speed decelerates to100km/h and auto- stop after 2 seconds of the bike/vehicle stop then returnsthe over counted 2 seconds automatically..FUNCTIONSBUTTON OPERATIONSMODE Button1.Press the MODE button to move between all functions in sequence as “ ”from one function screen to another when the speed sensor does not detect anysignal input.2.Press the MODE button to move partial functions in loop sequence as “ ”when speed sensor detects signal input.Max. 8mmVibration DirectionsensorMax. 8mmVibration DirectionsensorFunctions SpecificationsSymbolBar speedometer* 250 km/h for model #254 & 25X onlyBar tachometer 12,000 rpm for model #354 & 5XX onlyModels and IndicatorsMD085-X52MD085-X54MD085-X56MD085-X59RPM10R-0413264 |
Related manuals for Acewell ACE-MD085-254
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine