Acewell MA-085-3 Series User Manual
ATV/Motorcycle/Scooter/Vehicle ComputerMA-085-XXX-XX User ManualThanks for purchasing the ATV/Motorcycle/scooter/vehicle computer; this manual isspecifically designed for MA-085-XXX-XX series. MA-085-1XX/2XX series has needlespeedometer scale, weather MA-085-3XX/4XX/5XX/6XX series has different needletachometer scales, each series has different models, each model has different LEDindicators. You may find that the photo has a set of LED indicators different from yourcomputer, the photo is for reference only.Different series with different needle tachometer or speedometer scales are as bellows:MA-085-21X: 210Km/H MA-085-3XX: 6000rpmMA-085-26X: 260Km/H MA-085-4XX: 9000rpmMA-085-5XX: 12000rpmMA-085-6XX: 15000rpmThe last suffix “–XX can be identified up case material of bezel as bellows:No. suffix: Plastic material.-AB: CNC aluminum bezel with anodizing mesh black treatment.-CP: CNC aluminum bezel with chrome plating treatment.1. Tachometer Scale2. Needle Tachometer /speedometer3. 1st row: Current & Max.Speedometer4. 2nd row: Other functions5. Gear Indicator6. RESET Button7. MODE Button8. RPM Shift Warning Indicator9. Bar Temperature gauge10. Bar Fuel gauge11. 8 LED indicatorsFEATURESPANEL DESCRIPTIONSNeedle tachometer or speedometer, integrated digital functions and 8 LEDindicators for different models.LCD displays needle speedometer, bar temperature and fuel gauges, gearindicator and one other function simultaneously.Gear indicator which calculates gear by comparing speed and RPM.An optional air temperature sensor can measure outside temperature.Fuel gauge full and empty resistances are fully adjustable and it can connect tosender units with resistance range up to 990 ohms. In reserve mode, the fuelgauge is not displayed and fuel symbol lights when the input wire is connectedto -ve. The gauge can be switched off entirely if not required.Flexible battery warning voltage setting from 11.0 to 15.0V.Speedometer can show nearest 1 or 0.1 mph or km/h speed if required by user.E.g. 100 or 100.5.Highly visible 3 shift warning LED indicator.Allows end user to adjust odometer when the odometer is less than 30km / 18.6milesUniversal wheel circumference setting range from 1 to 3999mm.Includes bracket, RPM sensing wire, hall or reed speed sensor, fitting kits,wiring harness, main unit sleeve and temperature sensor.Excellent water resistant, anti vibration structure and noise immunity design.RPM sensor mounting:1. Connect either the yellow or white wire to sense the RPM signal.2. The yellow wire can be wrapped around the spark plug lead.a.Signal strength from the ignition coil is dependent on coil type.b.Coil 2-5 turns around spark plug lead, the more turns the stronger thesignal. A weak signal will not show a reading on the screen whereas a verystrong signal will have a reading which is too high or very jittery. If thereading is incorrect then try putting the 1MΩresistor which is included in thebox inline in the sensor wire.3. If the signal is still unstable, please try to connect the white wire to either theECU rev counter output or to the primary side of the coil or to the pulse wire onan active spark plug cap.SPEED SENSOR Mounting:ACEWELL has several speed sensors; the unit may include one of them. Ifthe model is intended to be connected to a gearbox electronic speed output toobtain the speed reading, no speed sensor will be included.Reed Speed Sensor and Magnet:1. This sensor is universal sensor for motorcycle, find a rotating part to installmagnet (for example disk, sprocket or driveshaft) and a location to install thesensor where it can be aligned to the magnet.2. Align the center of the magnet to either of the sensor marking lines or the sideof the sensor. The magnet must not travel down the body of the sensor.3. Installing the sensor parallel to the vibration direction creates optionalanti-vibration effect.4. Make sure the gap between the magnet and the sensor is within 8mm.SPECIFICATIONSFunctions SpecificationsSymbolMaximum speedAverage speedTemperature 1Max. TemperatureTemperature 2Digital TachometerSpeedometer Km/h / MPHMAX SPDAVG SPD12rpm 100 19,900 rpm2.4-399.9 km/h (248.5 MPH)2.4-399.9 km/h (248.5 MPH)2.4-399.9 km/h (248.5 MPH)0 -180 / 32 -356 , HI or oFF<0 display -L-, >180 display -H-0.0~999.9 KM/624.9Miles0 - 999999 KM, 0-624999 Miles999.9-0 KM/Miles count downAM/PM 0:00’ – 11H59’ / 23H59’0 – 999999H0 – 99H59’59”0 – 999999H8-18VDC, battery voltage warning settableN, R, 1, 2,…8 gears and off mode9999km, 9999 hours or oFF1-7 Bar-Graphic or off mode1-7 Bars, Adjustable 10Ω -990Ω,reserve mode, or not displayed0 180 / 32 356MAXTRIP 1or2TRIP 12ODORTTTHRTTVPower Input DC 12VTachometer Sensor CDI or Ignition Coil SignalSpeed Sensor Reed or hall SensorTemperature Sensor Thermo SensorSpeed input divider setup 1-199 PulsesMaximum speed input frequency 7K HzWheel circumference setting 1mm-3999mmDimensions Ø85*56.1mmFUNCTIONSBUTTON OPERATIONSMODE Button1. Press the MODE button to move between all functions in sequence as “ ”from one function screen to another when the speed sensor does not detectany signal input.Max. 8mmVibration DirectionsensorMax. 8mmVibration DirectionsensorFunctions SpecificationsSymbolNeedle SpeedometerNeedle TachometerMA-085-21X 210Km/HMA-085-26X 260Km/HMA-085-3XX 6,000rpmMA-085-4XX 9,000rpmMA-085-5XX 12,000rpmMA-085-6XX 15,000rpmMain Unit Installation:Spring WasherWasherRubber PadFixing Screw NutScrewBracketMain unit sleeveMain UnitHall Effective Speed Sensor and Magnet:1. This is universal sensor for ATV or motorcyclefront or rear wheelinstallation or motorcycle front wheel installation. For some fitmentsan accessory speed sensor holder may need to be purchased.2. Find a rotating part to install magnet (for example disk, sprocket ordriveshaft) and a location to install the sensor where it can be alignedto the magnet3. Align the center of the magnet to center of side face of the sensor.4. Make sure the gap between the magnet and the sensor is within 5mm.Specific Hall sensors:Cable drive adaptors for most bikes originally fitted with cable drivenspeedometers or odometers are available. When using these cables itis necessary to divide the circumference setting by the number ofrotations of the cable per rotation of the wheel.Thermo Sensor and Sensor Tube:1. The unit includes a water temperature sensor; you may have topurchase a suitable water pipe temperature sensor tube to installthe sensor on some bikes.2. Cut the water pipe, insert the temperature tube into the pipe andsecure it by attached pipe clamps.3. Screw the sensor into the tube.4. If your vehicle is fitted with a thermostat that stops water flowing tothe radiator when the engine is cold, you will not get a reading untilthe thermostat opens.5. Custom sensors are available for carburetted bikes to replace theoriginal sensor.RPM: Digital Tachometer1. It displays digital tachometer up to 19,990RPM and displays 19,999rpm when tachometer is over 20,000rpm..2. It has 2 wires to pick up RPM signal, the yellow wire is to connect toPlug,and white wire is for signal from ECU or Ignition coil.Shift Warning RPM1. The function enables you to set up a shift warning RPM.2. The yellow indicator flashes when RPM reaches 500rpm before setting value.3. The orange indicator turns on when RPM reaches setting value.4. The red indicator turns on when RPM reaches 500rpm more setting value.5. Each indicator turns off or stops flashing after you shift gear.Km/H or MPH: Speedometer1. Displays speed mete r up to 399.9 Km/H or 248.5 MPH.2. The maximum frequency of software divider is 7K Hz.3. With a small wheel size and large number of pulses per wheelrevolution it may not be possible to display very high speeds.MAX: Maximum Speed MeterDisplays highest speed achieved since last Reset operationAVG: Average Speed MeterIt calculates average speed from last RESET. The AVG is calculated fromTRIP1 be divided by RT.TRIP 1or2: Trip Meter 1or2TRIP function accumulates trip distance since last RESET as long as bike/vehicle is moving.TRIP 12: Trip Meter 31. TRIP-3 function appears and starts to accumulate trip distance automaticallyafter low fuel warning LED is turned on.2. RIP-3 be reset to zero automatically when fuel is added to over the low fuelwarning level.ODO: Odometer1. ODO accumulates total distance traveled.2. ODO datemory and cannot be reset.RT: Riding Timer1. Calculates total running time since last RESET.2. Counter automatically begins with movement.TT: Total Riding Timer1. Calculates total riding time from the beginning of the bike.2. TT data is stored in memory, and cannot be reset.HRTT: Hour Meter1. Calculates total engine operation time since installation RESET.2. Count automatically begins with engine starting.3. HRTT data is stored in memory, and cannot be reset.: 12/24 hour ClockIt displays 12 or 24 hour current time.1 and 2: Temperature Meter 1 & 21. It measures and displays from 0 -180 / 32 -356 .2. It displays -L- or -L- when temperature is lower than 0 (32 ) ordisconnected temperature sensor, and displays -H- or –H- when temperatureis over 180 or 356 ..3. User can measure engine temperature with sensor 1 and ambient air temperaturewith sensor 2.4. The bar-temperature and digits of temperature as well temperature LED indicatorflash when the thermo sensor detects temperature higher than the maximumpreset temperature.MAX 1&2: Maximum Temperature 1 & 2Displays highest temperature achieved since last Reset operation.: Digital Voltage and Battery Warnings1. It checks bike’s battery and charging systems health.2. It has 3 modes to be set, b-on, b-oFF and b-HI, all 3 modes range is from 11.0V to15.0V.3. The “b-on” means battery warning on voltage, when the voltage falls below thisthe LED will flash.4. The “b-off” means battery warning off voltage, b-off voltage must larger than b-onvoltage.5. The “b-HI” means battery high voltage, it comes on to warn that the batter hasover charging.: Gear Indicator1. The gear indicator calculates gear by comparing speed and RPM then displays gearposition.2. User has to train the gear indicator before use it.SCAN: Scan function1. The 2nd row of LCD data will be changed automatically every preset number ofseconds if the SCAN is selected. The scan period is from 1 to 20 seconds.2. All functions will be manual operations when SCAN is switched off.: Fuel Gauge1. Has 7 bars to indicate how much fuel remains.2. To use as a fuel gauge, it built-in F10 E250, F10 E510, F30 E80, F100E10,F250E10,F510E10,F80 E30 OFF Ohm fuel sender resistance, FXXX means full fuel resistance,EXXX means empty fuel resistance, the fuel bars will disappear when you select“OFF” mode. Last bar flashes to indicate low fuel level automatically. F30 E80 andF80 E30 are for vehicle application.3. To use as a reserve indicator, connect the reserve switch to the input and put into“RES” mode. When the switch pulls the input to –ve the backlight will flashdifferent color and the last fuel-bar flash. On vehicles with temperature basedsensors a 68 ohm 5w resistor needs to be connected between the input wire and12v (switched)4. If the gauge is not required they can be switched off: Bar Thermometer*1. Has 7 bars to indicate engine temperature.2. The 4th bar counts from bottom be turned on and over temperature LED flasheswhen thermometer reaches the preset warning temperature, each +/-15 lightson/off a bar base on the 4th bar.3. The bar-temperature flashes when the measured temperature is higher than thepreset warning temperature.Speed decimal option:1. User can decide to display speed to 1 or 0.1 mph / km/h.2. Follow the item 11 of set up mode to option the decimal of speedometer.Trip or HRT: Maintenance Reminder1. The maintenance reminder can set by either trip meter or hour meter, and an“Off” mode to switch it off.2. The trip meter maintenance can be set up to 9999km.3. The HRT maintenance reminder can be set up to 9999 hours.Bar-TemperatureBar-Fuel GaugeTrip meter 1or2Trip meter 3Odometer12/24 Hour ClockRiding timerTotal Riding TimeHour meterVoltage GaugeGear indicatorMaintain reminderSleeve Rubber PadTrip or HRTModels and Indicators*X is for 3, 4 and 5, 6 XX is for 21 and 26MA085-X52MA085-3XXMA085-4XXMA085-5XXMA085-6XXMA085-21XMA085-26XMA085-X54MA085-X56MA085-XX3MA085-XX5MA085-XX6Series |
Related manuals for Acewell MA-085-21 Series
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine