Acewell CA-085-15 Series User Manual
  |
ATV/Motorcycle/Scooter/Vehicle ComputerCA-085-1XX/2XX-XX User ManualThanks for purchasing the ATV/Motorcycle/scooter/vehicle computer; this manual isspecifically designed for CA-085-1XX/2XX-XX series. It has needle speedometer scale,each series has different models, each model has different LED indicators. You may findthat the photo has a set of LED indicators different from your computer, the photo is forreference only.Different series with different needle tachometer or speedometer scales are as bellows:CA-085-15X: 150Km/HCA-085-21X: 210Km/HCA-085-26X: 260Km/HThe last suffix “–XX can be identified material of the upper bezel as bellows:No. suffix: Plastic material.-AB: CNC aluminum bezel with anodizing mesh black treatment.-CP: CNC aluminum bezel with chrome plating treatment.Models and Indicators1. Needle Tachometer /speedometer2. Digital LCD display3. 6 LED indicators4.RESET Button5.MODE Button6.RPM Shift Warning IndicatorFEATURESPANEL DESCRIPTIONSClastic 85mm needle speedometer or tachometer with digital LCD display.LCD shows digital functions of speedometer, tachometer, maximum RPM andSPD, average speed, trip meter 1/2, odometer, riding time, total riding time, totalhour meter, volt meter, temperature meter, volt meter and clock.Integrates 6 LED warning lamps with different symbols depending on model.Built-in RGB LED backlight, user can adjust his/her prefer backlight color.Backlight can be switched on independently.Fast processor so can connect to pulse type gearbox speed sensors.Allows end user to adjust odometer when the odometer is less than 30km / 18.6miles.Universal wheel circumference setting range: 1-3999mm.CA-085-1XX/2XX includes main unit, bracket, RPM sensing wire, speed sensor,fitting kits, wiring harness and sleeve of main unit.Excellent water resistant, anti-vibration structure and noise immunity design.RPM sensor mounting:1. Connect either the yellow or white wire to sense the RPM signal.2. The yellow wire can be wrapped around the spark plug lead.a. Signal strength from the ignition coil is dependent on coil type.b. Coil 2-5 turns around spark plug lead, the more turns the stronger thesignal. A weak signal will not show a reading on the screen whereas avery strong signal will have a reading which is too high or very jittery. If thereading is incorrect then try putting the 1MΩresistor which is included in thebox inline in the sensor wire.3. If the signal is still unstable, please try to connect the white wire to either theECU rev counter output or to the primary side of the coil or to the pulse wire onan active spark plug cap.SPEED SENSOR Mounting:ACEWELL has several speed sensors; the unit may include one of them. Ifthe model is intended to be connected to a gearbox electronic speed output toobtain the speed reading, no speed sensor will be included.Reed Speed Sensor and Magnet:1. This sensor is universal sensor for motorcycle, find a rotating part to installmagnet (for example disk, sprocket or driveshaft) and a location to install thesensor where it can be aligned to the magnet.2. Align the center of the magnet to either of the sensor marking lines or theside of the sensor. The magnet must not travel down the body of the sensor3. Installing the sensor parallel to the vibration direction creates optionalanti-vibration effect.4. Make sure the gap between the magnet and the sensor is within 8mm.SPECIFICATIONSFunctions SpecificationsSymbol*Temperature MeterMAX SPDMAX RTMAX RPMMAX TEMPAVGrpm 100 19,900 rpm100 19,900 rpm0 -180 / 32 -3560-999999H0-999999HAM/PM 0:00’ – 11H59’ / 23H59’2.4-399.9 km/h (248.5 MPH)0.00-999.99 KM /624.99Miles2.4-399.9 km/h (248.5 MPH)0-99H59`59``2.4-399.9 km/h (248.5 MPH)0 -180 / 32 -356 , HI or Off<0 display -L-, >180 display -H-0 - 999999 KM, 0-624999 Miles8-18VDC, battery voltage warning settable0-9999kmODOTTHRTTVTripPower Input DC 12VTachometer Sensor CDI or Ignition Coil SignalSpeed Sensor Reed or hall Sensor for CA-085-1XX/2XX only.*Temperature Sensor Thermo Sensor for CA-085-3/4/5/6XX onlySpeed input divider setup 1-199 PulsesMaximum speed input frequency 7K HzWheel circumference setting 1mm-3999mmDimensions Ø85*56.1mmFUNCTIONSBUTTON OPERATIONSMODE ButtonPress the MODE button to move partial functions in loop sequence as “ ”from one function screen to another.RESET ButtonReset button cycles through functions in reverse orderMax. 8mmVibration DirectionsensorMax. 8mmVibration DirectionsensorFunctions SpecificationsSymbolNeedle SpeedometerKm/h / MPHSpeedometerTrip meter 1&2CA-085-15X 150Km/HCA-085-21X 210Km/HCA-085-26X 260Km/HTEMPMain Unit Installation:Spring WasherWasherRubber PadSleeve Rubber PadFixing Screw NutScrewBracketMain Unit SleeveMain UnitHall Effective Speed Sensor and Magnet:1. This is universal sensor for ATV or motorcyclefront or rear wheelinstallation or motorcycle front wheel installation. For some fitmentsan accessory speed sensor holder may need to be purchased.2. Find a rotating part to install magnet (for example disk, sprocket ordriveshaft) and a location to install the sensor where it can be alignedto the magnet3. Align the center of the magnet to center of side face of the sensor.4. Make sure the gap between the magnet and the sensor is within 5mm.Specific Hall sensors:Cable drive adaptors for most bikes originally fitted with cable drivenspeedometers or odometers are available. When using these cables itis necessary to divide the circumference setting by the number ofrotations of the cable per rotation of the wheel.*Thermo Sensor and Sensor Tube:1. The unit includes a water temperature sensor; you may have topurchase a suitable water pipe temperature sensor tube to installthe sensor on some bikes.2. Cut the water pipe, insert the temperature tube into the pipe andsecure it by attached pipe clamps.3. Screw the sensor into the tube.4. If your vehicle is fitted with a thermostat that stops water flowing tothe radiator when the engine is cold, you will not get a reading untilthe thermostat opens.5. Custom sensors are available for carburetted bikes to replace theoriginal sensor.Needle Speedometer:1. Indicates speedometer by analogue needle.2. Speedometer Scale shows the needle maximum speed of the model asbellows:CA-085-15X: 150Km/HCA-085-21X: 210Km/HCA-085-26X: 260Km/HRPM: Digital Tachometer1. It displays digital tachometer up to 19,990RPM and displays 19,999rpm when tachometer is over 20,000rpm..2. It has 2 wires to pick up RPM signal, the yellow wire is to connect to Plug,and white wire is for signal from ECU or Ignition coil.Shift Warning RPM1. The function enables you to set up a shift warning RPM.2. Shift warning LED indicator flashes when RPM reaches setting value, andstops flashing after you shift gear.MAX RPM: Maximum TachometerDisplays highest tachometer achieved since last Reset operation.SPD: Speedometer1. Displays speed meter up to 399.9 Km/H or 248.5 MPH.2. The maximum frequency from speed sensor is 7K Hz.3. With a small wheel size and large number of pulses per wheel revolution itmay not be possible to display very high speeds.MAX SPD: Maximum Speed MeterDisplays highest speed achieved since last Reset operation.AVG: Average Speed MeterIt calculates average speed from last RESET. The AVG is calculated from TRIP bedivided by RT.TRIP 1 or 2: Trip Meter 1 or 2TRIP function accumulates trip distance since last RESET as long as bike/vehicleis moving.ODO: Odometer1. ODO accumulates total distance traveled.2. ODO data is adjustable when it is less than 30km (18.6 Miles), after that it storedin memory and cannot be reset.RT: Riding Timer1. Calculates total running time since last RESET.2. Counter automatically begins with movement.TT: Total Riding Timer1. Calculates total riding time from the beginning of the bike.2. TT data is stored in memory, and cannot be reset.HRTT: Total Hour Meter1. Calculates total engine operation time since installation RESET.2. Count automatically begins with engine starting.3. HRTT data is stored in memory, and cannot be reset.: 12/24 hour ClockIt displays 12 or 24 hour current time.*TEMP: Temperature Meter1. It measures and displays from 0 -180 / 32 -356 .2. It displays -L- or -L- when temperature is lower than 0 (32) ordisconnected temperature sensor, and displays -H- or –H- whentemperature is over 180 or 356..3. The LCD backlight flash red and green in turn and temperature LED indicator(for models with temperature warning indicator only) flash when the thermosensor detects temperature higher than the maximum preset temperature.*MAX TEMP: Maximum TemperatureDisplays highest temperature achieved since last Reset operation.: Digital Voltage and Battery Warnings1. It checks bike’s battery and charging systems health.2. Indicates range 8-18VDC.+TRIP: Maintenance Reminder1. The maintenance reminder is set by trip meter, and an “Off” mode to switch it off.2. The trip meter maintenance can be set up to 9999km.TRIP 1or 212/24 Hour ClockDigital TachometerAverage speedMaximum speedRiding timerMaximum RPM*Max. TemperatureOdometerTotal Riding TimeHour meterVoltage GaugeMaintain reminderMode ResetResetResetResetResetResetResetModeModeModeModeModeModeReset ModeReset ModeReset ModeReset ModeReset ModeReset ModeReset ModeModeResetModeReset*Temperature sensor is an optional parts for these series, temperature functioncan be set On or Off by user, descriptions with “*” are for user who purchasesadditional temperature sensor reference only.CA085-XX3CA085-XX5CA085-XX6CA085-XX2*XX is for 15 , 21 and 26 |
Related manuals for Acewell CA-085-15 Series
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine