Canon PIXMA MP620 Series Getting Started

Also see for PIXMA MP620 series: Supplementary guide On-screen manual Manual Manual Manual

, Change the workgroup name to "WORKGROUP' following the procedure below.o Open the System Properties screen., Windows VistaClick Start, right-dick Computer, select Properties, then dick Change settings in theComputer name, domain, and workgroup settings column. User Account Controlscreen appears, dick Continue., Windows XP/2000Right-dick My Computer, then select Properties.6 Select the Computer Name tab, then click Change.o Change the workgroup name to "WORKGROUP', then dick OK.To open port 137:139:o Open the screen for setting Windows Firewall., Windows VistaClick Start> Control Panel> Allow a program through Windows Firewall. User Ac-count Control screen appears, dick Continue., Windows XP/2000Click Start> Control Panel> Security Center> Windows Firewall.6 Select the Exceptions tab, and dick Add port.o On the Add a Port dialog box, input the following information, and click OK.- Name: Input any name for the port.- Port number: Input "137".- TCP/UDP: Select TCP.() Repeat steps 6 and O.On the Add a Port dialog box, input the same information as you did in step 0 except forselecting UDP in TCP/UDP.o Use the same procedure to open the other ports (138TCP, 138UDP, 139TCP, and 139UDP).(} Confirm that the port names are added on the Exceptions sheet, and dick OK." If the problem is not resolved, click Skip to complete the installation without the networksetup of the Card Slot After installation is complete, to mount the Card Slot uSing the CanonIJ Network Tool, refer to "Using the Card Slot over a Network" in "About Network Com-munication' in "Appendix' of the on-screen manual: Advanced Guide. To mount the CardSlot manually, refer to "Cannot Mount the Card Slor in "About Network Communication" in"Troubleshooting" of the on-screen manual: Advanced Guide.sa~, If you connect to a network that is not protected with security measures, there is a risk ofdisclosing data such as your personal information to a third party.This message is displayed when installation of the network drive of the Card Slot fails duringsetup.Wait for a while, then dick Retry.The Enter Password dialog box is displayed if an administrator password is set to the machinewhich has already been set up.Admin PasswordEnter the administrator password you have set The administrator password consists ofalphanumeric characters and is no longer than 32 characters. The password is case sensitive.For security, your entry will be displayed by"·" (asterisks) for Windows and "." (bullets) forMacintosh.Security is not configured on the access point.The machine can still be used, so continue the setup procedure to complete it.(A) RetryClick to retry the network setup of the Card Slot.(B) SkipClick to continue installation without the network setup of the Card Slot.If it fails again after dicking Retry, follow the procedure below., Make sure that the computer is communicating with the network properly, then try again., Disable the Windows Firewall function, or open port 137:139 to allow communication with themachine following the procedure below. For information on other security software, refer to itsinstruction manual or contact its manufacturer., If you disabled the firewall function, disconnect your network from the Intemet To do this,configure your router not to connect to the Intemet or WAN., Make sure that a memory card is inserted in the Card Slot. If it is not inserted, insert it.To disable the Windows Firewall:o Open the screen for setting Windows Firewall., Windows VistaClick Start> Control Panel> Allow a program through Windows Firewall. User Ac-count Control screen appears, dick Continue., Windows XP/2000Click Start> Control Panel> Security Center> Windows Firewall.6 Select the General tab, check Off, then click OK.~~ , Depending on the Mac OS version, the authentication screen may appear. If it appears, clickOK.• If the problem is not resolved, click Skip to complete the setup without the network setupof the Card Slot To mount the Card Slot manually, refer to "Cannot Mount the Card Sior in"About Network Communication" in "Troubleshooting" of the on-screen manual: AdvancedGuide.5